Regency Panorama PG33LPG4-R Owners & Installation Manual Download Page 1

Page: 1 / 48

Models:

PG33NG4-R

PG33LPG4-R

Owners &
Installation

PLEASE KEEP THESE INSTRUCTIONS

FOR FUTURE REFERENCE

Man

ual

12.19.16

LISTINGS AND CODE APPROVALS

These gas appliances have been tested

in accordance with AS4533-2000, NZS

5262 and have been certified by the

Australian Gas Association for installa-

tion and operation as described in these

Installation and Operating Instructions.

Your unit should be serviced annu-

ally by an authorised service person.

918-649d

WARNING:

Improper installation, adjustment, altera-

tion, service or maintenance can cause

injury or property damage. Refer to this

manual. For assistance or additional in-

formation consult an authorised installer,

service agency or the gas supplier.
FOR YOUR SAFETY

Do not store or use gasoline or other flam

mable vapours and liquids in the vicinity of

this or any other appliance.
Installation and service must be performed

by an authorised installer, service agency or

the gas supplier.

Panorama

PG33

Gas Inbuilt

FOR YOUR SAFETY

What to do if you smell gas:

Do not try to light any appli-

ance

Do not touch any electri-

cal switch: do not use any

phone in your building.

Immediately call your gas

supplier from a neighbour's

phone. Follow the gas sup-

plier's instructions.

If you cannot reach your

gas supplier, call the fire

department.

Summary of Contents for Panorama PG33LPG4-R

















































Search results

Summary of Contents for Panorama PG33LPG4-R

Reviews:

Related manuals for Panorama PG33LPG4-R

Brands by name

Popular brands

Regency Panorama PG33LPG4-R, Owners & Installation Manual

Search results

Summary of Contents for Panorama PG33LPG4-R

Reviews:

Related manuals for Panorama PG33LPG4-R

Brands by name

Popular brands