manualshive.com logo in svg

Regency Greenfire GF1500L Series, Owners & Installation Manual

Share
Download
Regency Greenfire GF1500L Series Owners & Installation Manual Download Page 52

52     | 

Greenfire® GF1500L-2 Gas Fireplace

installation

Faceplate and Deflector Installation

919-593a

11.17.15

FACEPLATE AND DEFLECTOR INSTALLATION

2.   Install deflector by using 5 screws provided to the 

underside

 of 

the fascia as shown in Diagram 3 and 4. 

 

1.  Install the fascia to the unit by hooking the left and right side 

mounting brackets into the mounting slots at the side of the 
firebox as shown below. 

Diagram 3

Deflector 
Installed

3.  Hook the inner door frame to the unit as shown in 

diagram 6. 

 

Refer to “Screen and Inner Door Frame 

Installation” in the manual prior to installing it on to 
the unit. 

3 Mounting Slots

Diagram 1

4.   Remove any finger prints/ marks prior to operating 

the unit.  

 

Diagram 4

5 screws

Diagram 2

Diagram 4

Diagram 5

Diagram 6

NO

TE

•  There are 3 mounting slots available to accom-

modate any finishing that protrudes slightly beyond 

the faceplate.

•  It is recommended that you use the first mounting 

slot (the one closest to the door frame overlay) out 

of the 3 so that the faceplate and door frame over-

lay are flush with one another. See diagram 2.

W

ARNING

•  Turn off the unit at the wall switch or 

remote. Allow unit to cool for at least 10 

minutes prior to removing the faceplate. 

1

GF1500

Verona Faceplate Shown 

Summary of Contents for Greenfire GF1500L Series













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands