manualshive.com logo in svg

Regency Greenfire GF1500L Series, Owners & Installation Manual

Share
Download
Regency Greenfire GF1500L Series Owners & Installation Manual Download Page 18

18     | 

Greenfire® GF1500L-2 Gas Fireplace

installation

508.0

127.5

75 min.

358

77

TV Recess with 45 Degree Elbow

TV Recess with Vertical Venting

IMPOR

TANT

•  The clearances noted are recommended only and not a guarantee of compliance with all TV manufacturers’ maximum 

allowable operating temperatures. 

•  It is the responsibility of the user to check the TV installation instructions to ensure that the location of the TV in relation 

to the fireplace is suitable. 

•  Most television manufacturers instruct the user to not place the television above any heat source. Doing so may negatively 

affect the longevity of the television and may negate the warranty. 

•  If you do place a television above the fireplace, please be aware of the large amount of heat the fireplace generates. Regency 

in no way guarantees or takes responsibility for the suitability of the above installation for all homes, or any negative impacts 
from placing a TV above the fireplace, including damage to the TV.

127.5 mm 
max.

75 mm 
min.

508 mm min.

358 mm min.

77 mm max.

51 mm 
min.

Summary of Contents for Greenfire GF1500L Series













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands