Regency FireGenie PG36D Owners & Installation Download Page 4

Page: 4 / 48

Regency

PG36D Gas Log Fireplace

DATA BADGE

This is a copy of the label that accompanies each
PG36D Gas Fireplace. We have printed a copy
of the contents here for your review.

DO NO T

OPERATE THIS APPLIANCE BEFORE READING THE
INSTRUCTIONS BOOKLET.
PLACE ARTICLES ON OR AGAINST THIS APPLIANCE
STORE CHEMICALS OR FLAMMABLE MATERIALS

SPRAY AEROSOLS IN THE VICINITY OF THIS

APPLIANCE WHILE IN OPERATION.

OPERATE WITH PANELS, COVERS OR GUARDS
REMOVED FROM THIS APPLIANCE.
ENCLOSE THIS APPLIANCE.
MODIFY THIS APPLIANCE.

NEAR THIS APPLIANCE.

DO NO T

908-602a

(Australia Only)

The label is located on the front inside base of the
unit, visible when the bottom louvre is open.

DATA BADGE NOTE:

Regency

units are

constantly being improved. Check the label on
the unit and if there is a difference, the label on
the unit is the correct one.

Summary of Contents for FireGenie PG36D

















































Search results

Summary of Contents for FireGenie PG36D

Reviews:

Related manuals for FireGenie PG36D

Brands by name

Popular brands

Regency FireGenie PG36D, Owners & Installation

Search results

Summary of Contents for FireGenie PG36D

Reviews:

Related manuals for FireGenie PG36D

Brands by name

Popular brands