Regency Energy E18E Owners & Installation Manual Download Page 59

Page: 59 / 104

Regency

E18E-11 Gas Fireplace Insert

| 59

installation

ZERO CLEARANCE FACEPLATE INSTALLATION

919-831a

11.29.17

1. Shut down existing unit and allow to cool to room temperature.

2. Turn off gas supply and disconnect electrical.

3. Remove all accessories from existing unit, ie. glass doors, louvers,

etc.

4. Remove any tiles, hearth or surround from existing unit (if required).

5. Disconnect gas supply from existing unit.

6. Cut away a perimeter of drywall around the existing unit to expose

the framing. See example below.

7. Uninstall existing unit from framing.

Cut drywall

Remove unit from framing

8. Disconnect venting from existing unit - remove carefully to avoid damage.

9. Remove existing unit from framed opening.

10. Measure framed opening and compare to dimension requirements.
Additional adjustments to framed opening may be required.

ZERO CLEARANCE FACEPLATE INSTALLATION

ZERO CLEARANCE FRAMING DIMENSIONS

Framing

Dimensions Description

E18E

Framing Height

36” (914mm)

Framing Width

37 - 7/16" (951mm)

Framing Depth

15-1/2" (394mm)

Electrical connection: 110v required
Fan must be on at all times to operate this unit.

)LQLVKHG)ORRU

1RWH

$OOIUDPLQJPD\

EHRIZRRGFRQVWUXFWLRQ

E18E

Summary of Contents for Energy E18E









































































































Search results

Summary of Contents for Energy E18E

Reviews:

Related manuals for Energy E18E

Brands by name

Popular brands

Regency Energy E18E, Owners & Installation Manual

Search results

Summary of Contents for Energy E18E

Reviews:

Related manuals for Energy E18E

Brands by name

Popular brands