Regency City 686-927 Owners & Installation Manual Download Page 34

Page: 34 / 124

34 | City Series CB60E-1

installer's information

Top rear standoffs

Unit Assembly Prior to Installation

Rear Standoffs

The 6 rear standoffs are already attached to the appliance. Do not remove

these standoffs. The 2 top rear standoffs are designed so that screws can be

used to secure the appliance to the rear wall if needed. Studs must be in this

location if choosing to screw this into studs.

ttoooollttiipp

Leveling legs

Leveling Legs

There are four levelling legs - two on each side, that can be adjusted (with

the supplied tool—found in the manual package) if required.

ttoooollttiipp

Remove the screws securing the unit to the pallet

Due to the size and weight (480 pounds shipping weight) of the CB60E-1 -

lifting and moving the unit will require 4 people.

Place a length (long enough to get a solid grip on each side) of 2 x 4 through

the opening on each side of the unit as shown.

Lift and move the unit carefully.

Note: Remove 2 x 4's when unit it is in final position.

Before you Start-Removing the Unit from the

Pallet

Summary of Contents for City 686-927





























































































































Search results

Summary of Contents for City 686-927

Reviews:

Related manuals for City 686-927

Brands by name

Popular brands

Regency City 686-927, Owners & Installation Manual

Search results

Summary of Contents for City 686-927

Reviews:

Related manuals for City 686-927

Brands by name

Popular brands