Regency City 686-927 Owners & Installation Manual Download Page 83

Page: 83 / 124

City Series CB60E-1 | 83

installation

Levers to lower firebox glass

tooltip

6. Support the glass with one hand and open the 9 lower clamps.

5. Pull the 3 lower glass gasket pads forward to release the glass.

7. Locate the 2 levers below the glass and turn them both 90° in a clockwise

direction to lower the firebox glass panel.

8. Carefully lean glass forward onto supports.

Glass panel--leaning on supports

Lower clamps (x9) in open position

Push down on levers to lower glass panel

Gasket pad

NOTE:

The firebox glass may remain propped on the glass supports to clean

the interior surface. Use care when cleaning -- do not apply excessive force

or pressure.

To remove the firebox glass panel from the unit:

tilt the glass forward

gently onto the glass supports, grip both suction clamps and lift the glass

up and out of the unit.

10. To install glass--reverse steps.

IMPORTANT:

Remove glass panel completely when installing or removing

panels, logs, media, etc. to avoid causing any damage to the glass.

Summary of Contents for City 686-927





























































































































Search results

Summary of Contents for City 686-927

Reviews:

Related manuals for City 686-927

Brands by name

Popular brands

Regency City 686-927, Owners & Installation Manual

Search results

Summary of Contents for City 686-927

Reviews:

Related manuals for City 686-927

Brands by name

Popular brands