Regency City 686-927 Owners & Installation Manual Download Page 28

Page: 28 / 124

28 | City Series CB60E-1

owner's information

Optional Front Barrier Glass Stoppers Installation / Removal

There are 4 optional stoppers (2 side/2 front) included in the manual pack

which provide additional support to the glass barrier, if desired--install the

stoppers prior to installation of the barrier glass.

4. Repeat steps 1-6 to install outer panels on opposite side.

5. Install barrier glass as per instructions in this manual.

3. Install glass stopper (if desired) by sliding stopper assembly between unit

and panel - the stopper assembly will attach to the unit via a magnet,

adjust position of glass stopper is required.

2. Slide backwall outer panel behind glass stopper bracket (if installed).

1. Install glass stopper (if desired) by sliding down the outside of the

outer side panel.

Summary of Contents for City 686-927





























































































































Search results

Summary of Contents for City 686-927

Reviews:

Related manuals for City 686-927

Brands by name

Popular brands

Regency City 686-927, Owners & Installation Manual

Search results

Summary of Contents for City 686-927

Reviews:

Related manuals for City 686-927

Brands by name

Popular brands