background image

 

U900E-11 Gas Fireplace  |    5

Non-Combustible Facing Installation 

Non-combustible board

Non-combustible board-faces and edges
MUST BE PRIMED.

Non-combustible board

shipped with unit

shipped with unit

Caution:

 

The non-combustible board supplied with this unit can    

    

          

be damaged if dropped or struck.  

Handle with care

.

1.   

Using drywall screws

 - 

secure non combustible material 

      around unit, framing and top nailing strip every 6 inches. 

Important Note: 

To avoid cracking the board - pre-drill holes prior to          

     

securing to unit/ framing.

2.

   Wipe any debris/dust from the non combustible 

       material and drywall.

3

.    Prior to securing it is mandatory to prime the facing and edges using a quality 

primer. This will ensure proper adhesion of both the tape and mud.  The 
supplied board is very porous. 

      Failure to follow this procedure will result in cracked seams.

4.

   Tape the seams using a mesh type tape.

5.

   Mud seams as normal. We recommend using a 

      product called Durabond high strength compound - for the first coat.
      This product can be found at any hardware store. 
      Mud must be cured as per manufacturer’s recommendations.

6.

  Prime wall for a second time for proper adhesion of paint

7.

  Paint walls using a high quality paint which will withstand 

      the high temperatures being emitted from this appliance.

Non-Combustible Requirements

* Installation of the ON/OFF Wall Switch/Battery Holder must be completed before installing non-combustible facing.

All three pieces (top, 2 sides) may be ordered separately to meet the non combustible requirements.  

Calcium silicate board is a high - grade material
with cement, quartz, natural and selected
minerals as the main raw materials. It is widely
used for partitions and ceilings in buildings.
It is fire proof and earthquake proof.

If finishing the wall above the unit with materials
such as tile, brick, marble, etc. non-combustible
board available from the building supply store
can be used.

Note: 

Calcium Silicate is 1/2' thick 

NOTE:

  A  minimum  thickness 

of 1/2" non combustible facing 
is required. 

U900E-11 Gas Fireplace

Summary of Contents for U900E-11














Reviews: