background image

 

U900E-11 Gas Fireplace  |    11

Vertical Venting with Three (3) 90

o

 Elbows

One 90

o

 elbow = Two 45

o

 elbows

Option

V

H + H1

V + V1

With these options, 
max.  total  pipe 
length  is  30  feet 
with min. of 10 feet 
total  vertical  and 
max.  8  feet  total 
horizontal.

Please note min. 
1 foot between 
90

o

 elbows is re-

quired.

A)

0' Min. 2' Max.

2' Min.

B)

1' Min.

2' Max

3' Min.

C)

2' Min.

3' Max

4' Min.

D)

3' Min.

4' Max

6' Min.

E)

4' Min.

5' Max

7' Min.

F)

5' Min.

6' Max

8' Min.

G)

6' Min.

7' Max

9' Min.

H)

7' Min.

8' Max

10' Min.

Restrictor Set 0 - 3" Factory Setting

Horizontal Venting with Three (3) 90

o

 Elbows

One 90

o

 elbow = Two 45

o

 elbows

Horizontal Venting with Two (2) 90

o

 Elbows

One 90

o

 elbow = Two 45

o

 elbows

Option

V

H + H1

With these options, maxi-
mum total pipe length is 30 
feet with minimum of 6 feet 
total vertical and maximum 
8 feet total horizontal.

Please note minimum 1 
foot between 90

o

 elbows 

is required.

 A)

1'  Min. 3' Max.

B)

2'  Min. 4' Max.

C)

3'  Min. 5' Max.

D)

4'  Min. 6' Max.

E)

5'  Min. 7' Max.

F)

6' Min.

8' Max.

Restrictor Set 0 - 3" Facto-
ry Setting

Option

V

H

V + V1

H + H1

With  these  op-
tions, max. total 
pipe  length  is 
30 feet with min. 
of  12  feet  total 
vertical and max. 
9 feet total hori-
zontal.

Please note min. 
1 foot between 
90

 elbows is 

required.

A)

0' Min. 1' Max.

1' Min.

2' Max.

B)

1' Min. 2' Max.

3' Min.

3' Max.

C)

2' Min. 2' Max.

5' Min.

4' Max.

D)

3' Min. 2' Max.

7' Min.

5' Max.

 E)

4' Min. 3 Max.

9' Min.

6' Max.

 F)

5' Min. 4' Max. 10' Min.

7' Max.

G)

6' Min. 5' Max. 11' Min.

8' Max.

H)

7' Min. 6' Max. 12' Min.

9' Max.

Restrictor Set 0 - 3" Factory Setting

U900E-11 Gas Fireplace

Summary of Contents for U900E-11














Reviews: