Regency Fireplace Products Horizon HZ54E-LP Owners & Installation Manual Download Page 33

Page: 33 / 68

Regency Horizon HZ54E-1 Gas Fireplace

INSTALLATION

An optional AC power adaptor may be installed as a constant power source for the SureFire system.

NOTE: AC power adaptor is not required when using GTMF Remote

IMPORTANT: Recommend removing the 4-AA batteries in the SureFire receiver.

This will avoid battery leakage and power drainage. 4-AA Battery pack may be re-installed into receiver during power outages.

NOTE: For all

Gas Fireplaces

120 volt power must be brought to the

receptacle box

inside the

ERWWRPRIWKH¿UHER[

(provided with the unit).

All Freestanding

Gas Stoves

& Gas

Inserts

will need a

receptacle box

located

outside / near the unit

so that the AC Power Adaptor can be plugged in.

INSTALL AC ADAPTOR WITH SUREFIRE WALL SWITCH ONLY - (WITHOUT REMOTE)

INSTALL AC ADAPTOR WITH SUREFIRE PROFLAME GT / GTM REMOTE

Locate “DC Supply” tag on wire harness. For location in unit

see remote installation page in owners manual.

919-063

03/04/2013

Connect the male end from AC adaptor to the female end

tagged “DC Supply” on wiring harness in unit.

Locate FCM - COM connector on the Remote wire harness -

see manual for location in unit.

Plug in wire adaptor to FCM - COM connector - be careful not

WRGDPDJHHQGV7KLVRQO\¿WVRQHZD\'R1RW)RUFHLQZURQJZD\

Plug AC adaptor into 120V wall outlet (or into 120V receptacle if

LQVWDOOHGLQVLGHWKHJDV¿UHSODFH¿UHER[

Neatly tuck any loose AC Power Adaptor wires neatly underneath /
inside the appliance.

Note:

(QVXUHWKDWZLUHVGRQRWWRXFKWKHXQGHUVLGHRIWKH¿UHER[

(keep wires away from the heat as much as possible).

FCM - COM

AC adaptor

wire adaptor

Connect the male end of the AC adaptor to the female end of the
wire adaptor (supplied with AC adaptor) together as shown

AC adaptor

Wire adaptor

FCM - COM

Plug AC adaptor into 120V wall outlet (or into 120V receptacle if

LQVWDOOHGLQVLGHWKHJDV¿UHSODFH¿UHER[

Neatly tuck any loose AC Power Adaptor wires neatly underneath /
inside the appliance.

Note:

(QVXUHWKDWZLUHVGRQRWWRXFKWKHXQGHUVLGHRIWKH¿UHER[

(keep wires away from the heat as much as possible).

This method also applies for models, HZ30E - HZ40E - L390E - HZI390E

AC POWER ADAPTOR INSTALLATION (FOR SUREFIRE SYSTEMS)

Summary of Contents for Horizon HZ54E-LP





































































Search results

Summary of Contents for Horizon HZ54E-LP

Reviews:

Related manuals for Horizon HZ54E-LP

Brands by name

Popular brands

Regency Fireplace Products Horizon HZ54E-LP, Owners & Installation Manual

Search results

Summary of Contents for Horizon HZ54E-LP

Reviews:

Related manuals for Horizon HZ54E-LP

Brands by name

Popular brands