Regency Fireplace Products Classic F2450M Owners & Installation Manual Download Page 24 | Manualshive

Page: 24 / 44

background image

24

|

F2450M Regency Freestanding Woodstove

installation

Stainless Steel Smoke Deflector Installation

The stainless smoke deflector is located in the upper front area of the firebox. The deflector is held in place with 2 bolts
Prior to the first fire, ensure deflector is seated properly and secured with 2 hand tightened bolts.

To replace the deflector, loosen off both bolts and slide defector upward and out. Install new deflector and hand tighten bolts. Ensure positive location of
the defector prior to hand tightening.

WARNING:

Operation of the unit with out proper installation of smoke deflector will void warranty.

Smoke deflector installed with 2 bolts.

Note:

This is a view from the back of the unit

through the top.

Smoke deflector is installed through the door
opening in location shown in diagram

Smoke deflector

Ensure deflector is seated so bolts are situated
at the top of the keyhole before tightening.

«
...
22
23
24
25
26
...
»

Summary of Contents for Classic F2450M













































Reviews:

No comments

Related manuals for Classic F2450M

Brand: Panadero Pages: 16

Brand: Palazzetti Pages: 16

Brand: Bubble Pages: 12

Brand: Heatilator Pages: 46

ROBY2500 CUISINIERE

Brand: J. A. Roby Pages: 31

WONDERWOOD 2931

Brand: United States Stove Pages: 12

Brand: Quadra-Fire Pages: 20

Brand: Atosa Pages: 24

Brand: Cadel Pages: 48

Brand: Cadac Pages: 5

Napoleon Haliburton GDS28-1NE

Brand: Wolf Steel Pages: 108

Brand: F2 Fires Pages: 16

Brand: HASE Pages: 44

Brand: Heartland Pages: 75

Brand: Drija Pages: 19

Brand: Primus Pages: 2

Brand: Primus Pages: 4

BELLUS HEROS 100

Brand: Faber Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands