Regency Fireplace Products Bellavista B41XTE Owners & Installation Manual Download Page 60

Page: 60 / 84

Regency Bellavista

B41XTE -11 Gas Fireplace

installation

919-425

08/21/14

B41XTCE / B41XTE

FAN INSTALLATION

TO REMOVE THE FAN

Shut the power off.

Reverse the above instructions.

Note:

The bearings are lubricated for life. Do not lubricate them. Make

sure you vacuum the fan area on a regular basis.

IMPORTANT:

These fans collect a lot of dust from within your

home. Ensure you maintain these fan motors on

a regular basis by vacuuming out the fan blades

and housing using a soft brush nozzle.

Slide the thermodisc/cover assembly onto the bracket clip on the

left underside of the firebox. Ensure that no wires will touch hot

surfaces.

. Plug in the fan power cord to the Fan Control Module into the outlet

marked “Fan”. Plug the FCM-COM wire from the remote control

wiring harness into the location on the Fan Control Module marked

“COM”. Turn the switch on the Fan Control Module to the ON posi-

tion. ON is to the left. The “O” is the off position

. See the Proflame instructions for coding the remote handheld to

the receiver and for operating instructions.

. Reverse Steps 2 -1 to complete the installation.

10.

Install the Fan Control Module (FCM) on to the left side base of

the unit and plug in to electrical receptacle in unit as shown.

FCM-COM Wire

FCM-COM wire

Fan Power Cord

Summary of Contents for Bellavista B41XTE





















































































Search results

Summary of Contents for Bellavista B41XTE

Reviews:

Related manuals for Bellavista B41XTE

Brands by name

Popular brands

Regency Fireplace Products Bellavista B41XTE, Owners & Installation Manual

Search results

Summary of Contents for Bellavista B41XTE

Reviews:

Related manuals for Bellavista B41XTE

Brands by name

Popular brands