Regency Fireplace Products Bellavista B41XTE Owners & Installation Manual Download Page 33 | Manualshive

Page: 33 / 84

background image

Regency Bellavista

®

B41XTE -11 Gas Fireplace

|

33

installation

Rigid Pipe Venting Systems-Basic Horizontal & Vertical Terminations

Rigid Pipe Vent Systems offer a complete line of component parts for installation of both horizontal and vertical installations. Many items are offered in decora-
tive black, as well as galvanized finish.

The minimum components required for a basic Horizontal Termination are:

1 AstroCap XL Termination Cap
1 90

o

Elbow

  1  Rigid Pipe Adaptor
  1  Wall Thimble
  1  Length of rigid pipe to suit wall thickness

The minimum components required for a basic
Vertical Termination are:

  1  Vertical Termination Cap
  1  Rigid Pipe Adaptor
  1  Lengths of pipe to adequately

penetrate roof

  1  Ceiling Firestop
  1  Flashing
  1  Storm Collar

Wall  thickness    is  measured  from  the  back
standoffs  to  the  inside  mounting  surface  of
termination cap. For siding other than vinyl, furring
strips  may  be  used,  instead  of  a  vinyl  siding
standoff, to create a level surface to mount the
vent terminal. The Terminal must not be recessed
into siding. Measure the wall thickness including
furring strips.

If a Vinyl Siding Standoff is required (it must be
used with vinyl siding), measure to outside surface
of wall without siding and add 2 inches.

Alternate Snorkel

Termination Cap

HOT

Alternate
Horizontal Termination
Caps

Rigid Pipe

Adaptor (770-994)

Pipe Length

Vertical Terminal

Storm Collar

Flashing

Ceiling Firestop

Pipe

Length

Pipe Length

90 Elbow

o

AstroCap XL

Termination Cap

(Part #946-623/P)

Wall Thimble

(Mandatory in all

Horizontal Terminations)

Vinyl Siding

Standoff (Optional)

Vent Guard - if required*

(Part #946-506/P)

When using Rigid Vent other than

Simpson Dura-Vent, 3 screws must be

used to secure rigid pipe to adaptor.

This product has been evaluated by Intertek
when using a rigid pipe adaptor and use of
any of the specific chimney systems listed in
this manual. Use of these systems with the
rigid pipe adaptor is deemed acceptable and
does not affect the Intertek WHI listing of these
components.

WARNING:

Do not combine venting components from
different venting systems.

Exception: However, use of the the AstroCap
XL

TM

is acceptable with all systems.

The Regency AstroCap

TM

and Regency Riser Vent terminal are certified for installations using Regency venting systems as well as any specific chimney

systems listed in this manual. AstroCap

TM

is a proprietary trademark of Regency Fireplace Products.

«
...
31
32
33
34
35
...
»

Summary of Contents for Bellavista B41XTE





















































































Reviews:

No comments

Related manuals for Bellavista B41XTE

Brand: Majestic Pages: 64

Brand: Jøtul Pages: 36

Brand: ELEMENTI Pages: 20

ROOM SEALED INSET LIVE FUEL EFFECT GAS FIRE

Brand: Paragon Fires Pages: 28

Brand: HAMPTON BAY Pages: 12

Brand: Bali Pages: 16

Brand: baltur Pages: 64

Brand: Dimplex Pages: 64

Brand: Superior Pages: 20

Gemini33xxx SERIES

Brand: Astria Pages: 82

Davos A High FP-DAV0A-10L

Brand: Nordpeis Pages: 60

Brand: Valor Pages: 24

Brand: M Design Pages: 14

Marquis MCVP42LP

Brand: Kingsman Fireplaces Pages: 75

Prescott White Mantel

Brand: Early Settler Pages: 4

Acies l38 Series

Brand: Napoleon Pages: 140

Isokern Maximus Linear 82L48ST

Brand: EarthCore Pages: 69

Brand: Mainstays Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands