Regency Fireplace Products Bellavista B41XTCE-LP10 Owners & Installation Manual Download

Page: 3 / 64

Regency Bellavista™ B41XTCE-10 Gas Fireplace

MANUFACTURED MOBILE HOME REQUIREMENTS

INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE

This Regency

product has been tested and listed by Warnock Hersey as a Direct Vent Wall Furnace to the following standards:

VENTED GAS FIREPLACE HEATERS ANSI Z21.88-2014 • CSA 2.33-2014 and GAS-FIRED APPLIANCES FOR USE AT HIGH

ALTITUDES CAN / CGA 2.17-M91.

This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured

Home Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.

This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local

codes follow the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A.,

and the current CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.

This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel chassis as applicable

to local codes.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with

the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.

This appliance may only be installed in an aftermarket permanently located, manufactured (U.S.A only) or mobile home, where not

prohibited by local codes.

This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible for use with other

gases.

Ensure that structural members are not cut or weakened during installation.

Bellavista

B41XTCE Video

Bellavista B36XT

Gas Fireplace Benefits

Summary of Contents for Bellavista B41XTCE-LP10

































































Search results

Summary of Contents for Bellavista B41XTCE-LP10

Reviews:

Related manuals for Bellavista B41XTCE-LP10

Brands by name

Popular brands

Regency Fireplace Products Bellavista B41XTCE-LP10, Owners & Installation Manual

Search results

Summary of Contents for Bellavista B41XTCE-LP10

Reviews:

Related manuals for Bellavista B41XTCE-LP10

Brands by name

Popular brands