Regada Rematic STR 1PA, Installation, Service And Maintenance Instructions, Page: 53 / 65

STR 1PA, STR 2PA 51
Terminals for STR PA for DMS3:
PE, N, L - terminals (0,05-1,5 mm
2
) of supply (24 V AC resp. 110/120 V AC, resp. 230/240 V AC, 50/60 Hz
(according to the specification – voltage and frequency are stated on nameplate of EA)
2, 3, 4 – terminals (max. 1,5 mm
2
) of supply of supply 3-phase motor 3x400 resp. 3x380 V AC
5,6 – terminals (max. 1,5 mm
2
) of supply of supply 3-phase motor 3x400 resp. 3x380 V AC
OP, CL – – terminals (max. 1,5 mm
2
) of output of control for without reverse unit
0 V, +24 V– terminals (max. 1,5 mm
2
) of output voltage 24 V DC (40 mA)
COM, CLOSE OPEN, I1, I2 – terminals (0,05 - 1 mm
2
) of control inputs 24 V DC
+IN, -IN, SH – terminals (0,05 - 1 mm
2
) of unified input current signal or voltage signal
+L, -L, SH – terminals (0,05 - 1 mm
2
) of output current signal (passive) 4-20 mA
COM, NO, NC, NO, NO – terminals (0,05 - 1,5 mm
2
) of relay READY, relay R1 a R2 (
on control unit
)
COM5, NO5, NC5 – terminals (0,05 – 1,5 mm
2
) relay RE5 (on the module of the additional relays)
COM1, RE4, RE3, RE2, RE1 – terminals (0,05 - 1,5 mm
2
) relay RE4, RE3, RE2, RE1 (on the module of the
additional relays)
COM, NO, NC – terminals (0,05 – 1,5 mm
2
) of relay READY (on the module of the additional relays)
Terminals for DMS3 Modbus/Profibus:
- screwless terminals are in separately terminal box. cross-section of connection wire 0,08 - 2,5 mm
2
PE,N,U,V,W - terminals of supply voltage 230 V AC and 3x400 V AC
1,2,3,4,5,6 – terminals of single channel interface Modbus/Profibus
7,8,9,10,11,12 - terminals of duo channel interface Modbus/Profibus
21,22 – terminals of output voltage 24 V DC (40 mA)
13,14,15,16,17 – terminals of control inputs 24 V DC (40mA)
Note 1: On terminal N, L terminal power supply (X) feed supply voltage 230 V AC, or 24 V AC by you - specified
type of construction EA. For supply voltage 24 V AC no need connect ground wire PE. For a version of EA with
the supply voltage 3x400 or 3x380V, terminals N, L on terminal board of power supply (X) are fed by power
supply 220 respectively
230 V AC.
Note 2: Program possibilities for R1, R2, RE1, RE2, RE3, RE4, RE5 relays: DISABLED, open position, close
position, torque-open, torque – close, torque open or torque close, torque open or position open, torque close or
position close, open, close, movement, movement flasher, to position, from position, warning, remote control,
local control, control shut off, relay READY
Program possibilities for
READY relay: errors, errors or warnings, errors or no remote, errors or warnings or no
remote.
Program possibilities for output signal (from
EPV passive): 4 to 20 mA, 20 to 4 mA.
Control programme options (regulating)(not valid for with Modbus/Profibus protocol): 2P, 3P, 3P/2P switched
over to I2
Program possibilities
for input control signal (N) : 4 to 20 mA (2 to 10 V), 20 to 4 mA (10 to 2 V), 0 to 20 mA (0
to 10 V), 20 to 0 mA (10 to 0 V).
Program possibilities - for Modbus protocol
address – 1 .... 247
baudrate [bit/s] – 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
parity – even, odd, No
redundancy – off, Cable, Component, Repeater
connect time [s] – 0,1 .... 25,5s
Program possibilities - for Profibus protocol
Address 1 – 1 ... 126
Address 2 – 1 ....126
Redundancy: - Off, Simple
Program possibilities for inputs I1 : DISABLED, ESD, DBL (local releasing, remote releasing - not valid for EA
without local control), STOP.
Program possibilities for
inputs I2 : DISABLED, ESD, DBL (local releasing, remote releasing), STOP
2P (when controller is switch on)(for control programme option 3P/2P I2)) allows control using the binary 24V DC
inputs with I2 input activated.
Program possibilities of
FAILURE REACTION : OPEN, CLOSE, STOP, SAFE POSITION.
The identical functions cannot be set on I1 &I2 inputs in addition to the disabled state (e.g., if the ESD function is
set on I1 input, it is not possible to select the (ESD) function on I2 input at the same time.
Relay READY on the control unit is doubled with relay READY on the module of the additional relays.
Relay R1 and relay R2 on the control unit is doubled with relay RE1 and relay RE2 on the module of the
additional relays.