Reflex Reflexomat Basic RS 90 / 1 Operating Manual Download Page 8

Installation 

 

 

 

8 —  English  

Reflexomat Basic — 20.09.2020 - Rev. A 

 

 

 

6.3.5

 

Fitting the level sensor 

ATTENTION 

 

Damage to the pressure load cell due to unprofessional installation 
Incorrect installation may result in damage to the "LIS" level sensor, 
malfunctioning and incorrect measurements from the pressure load cell. 
• 

Comply with the instructions regarding the installation of the pressure 
load cell. 

 
The "LIS" level sensor uses a pressure load cell. This pressure pick-up is to be 
installed after the primary vessel has been placed at its final position, see 
chapter 6.3.2 "Tank installation" on page 6 . Comply with the following 
instructions: 
• 

Remove the transport securing device (squared timber) at the vessel base 
of the primary vessel. 

• 

Replace this transport securing device with the pressure load cell. 

• 

Avoid shock-type loading of the pressure load cell by, for example, 
subsequent alignment of the vessel. 

• 

Use flexible hoses to connect the primary vessel and the first secondary 
vessel. 
–  

Use only the supplied connection sets, see chapter 6.3.2 "Tank 
installation"
 on page 6 . 

• 

Perform a null balancing of the filling level when the primary vessel is 
aligned and fully emptied, see chapter 9.2 "Configuring settings in the 
controller"
 on page 12 . 

 
Standard values for level measurements: 

 

Primary vessel 

Measuring range 

200 l 

0 – 4 bar 

300 – 500 l 

0 – 10 bar 

600 l 

0 – 25 bar 

 

6.4

 

Make-up and degassing variants 

6.4.1

 

Function 

The filling level is recorded in the primary tank by the "LIS" level sensor and 
evaluated in the controller. When the water level falls below the value specified 
in the controller's customer menu, the external make-up is activated. 
 
6.4.1.1

 

Make-up without pump 

Reflexomat Basic with solenoid valve and ball valve. 

 

 

 

Reflexomat Basic 

  WC 

Make-up pipe 

Solenoid valve "Fillvalve" with ball 
valve 

  LIS 

Level sensor 

Reflex Fillset 

  EC 

Expansion pipe 

ST  Dirt trap 

   

 

 

Preferably, you should use the Reflex Fillset with integrated system separator 
when using drinking water for make-up. If you don't use a Reflex Fillset, you 

must use an "ST" dirt trap with a mesh size ≥

 0.25 mm for the make-up. 

 

6.4.1.2

 

Make-up with pump 

Reflexomat Basic with Reflex Fillcontrol Auto 

 

 

 

Reflexomat Basic 

 

ST  Dirt trap 

Fillcontrol Auto 

 

EC  Expansion pipe 

WC  Make-up pipe 

 

LI

Level sensor 

 

Water make-up with Fillcontrol Auto is suitable for make-up at high system 
pressures of up to 8.5 bar. The "ST" dirt trap is part of the deliverables. 
 
6.4.1.3

 

Make-up with softening and degassing 

Reflexomat Basic and Reflex Servitec. 

 

 

 

Reflexomat Basic 

 

ST 

Dirt trap 

Reflex Servitec 

 

WC  Make-up pipe 

Reflex Fillsoft 

 

LIS  Level sensor 

Reflex Fillset Impulse 

 

EC  Expansion pipe 

 

The Reflex Servitec degassing and make-up station degasses the water from the 
system circuit and the make-up water. The automatic water make-up for the 
system circuit is controlled by the pressurisation system. Reflex Fillsoft 
additionally softens the make-up water. 
• 

Reflex Servitec degassing and make-up station, see chapter 4.6 "Optional 
equipment and accessories"
 on page 5 . 

• 

Reflex Fillsoft softening systems and Reflex Fillset Impulse, see chapter 4.6 
"Optional equipment and accessories"
 on page 5 . 

 

 

Note! 
When using Reflex Fillsoft softening systems, always install the Reflex 
Fillset Impulse. 
–  

The controller evaluates the make-up quantities and signals a 
required replacement of the softening cartridges. 

 

Summary of Contents for Reflexomat Basic RS 90 / 1




















Reviews: