background image

DANGER: Do Not install a wedge without removing the Lock-Out Bolts.  Never operate without a wedge if the Lock-Out bolts are 

not installed.  Doing this will create a double pivot and could result in death or serious injury and/or damage to the tow vehicle and 
trailer.  

Installation Instructions

16K Sidewinder

TM

©

2009, 2016 Cequent Performance Products - Printed in Mexico

Sheet 6 of 12 

SW16KIN

10/25/16

Rev. J

Form: F205 Rev A  5-6-05

ASSEMBLY INSTRUCTIONS – CON’T

Figure 17

OPERATION INSTRUCTIONS

The Sidewinder

TM

Pin-Box is very versatile and can be used as a standard pin box – Conventional Transport.  For 

conventional transport (2) ¾” GR 5 Bolts and Hardware are installed in the back of the unit (figure 17), on OE applications 
these come installed from the factory and may or may not have been removed by the dealer.  The two bolts prevent rotation 
and allow use of the pin-box without the wedge installed.        

Lock-Out Bolts

(Torque to 70 ft-lbs)

Lock-Out bolt kits are available for the 
16K Sidewinder

TM

P/N: 38024

Conventional Transport:

Sidewinder

TM

Transport:

Sidewinder

TM

Pin-Boxes equipped with lock-out bolts can be converted to activate the Sidewinder

TM

feature.  This feature 

moves the pivot from the truck bed to the pin-box mounting wings under the nose of the trailer and allows worry free towing 
up to 90º or more.  NOTE: Not all tow vehicle and trailer combinations will allow a 90 degree turn.

Note: Lock Out Bolts are only                   

supplied on OE units.

10.  Install the Sidewinder

TM

inside the mounting wings (Figure 15). Cequent Performance Products recommends replacing the 

mounting bolts, nuts, and lock washers with the same size & grade as the bolts removed from the original pin box.  

Torque all bolts to the proper value listed in table 1.

1/2” Bolts  GR5

90 ft-lbs

5/8” Bolts  GR5

150 ft-lbs

3/4” Bolts  GR5

275 ft-lbs

Bolt Diameter

Torque

Table 1

Figure 16

Bottom of Turret

CAUTION: The bottom of the turret must extend below the lowest point on the wings to allow the arm to clear during pivot. (Figure 16)                          

Figure 15

Lowest Point on Wings

Note:
When Sidewinder

TM

feature is 

activated, rotation of the arm 
manually, is not expected.

Summary of Contents for Sidewinder 16K
















Reviews: