background image

3

Introduction

Thank you for purchasing your REED R5700 Ground Resistance Tester. 
Please read the following instructions carefully before using your instrument. 
By following the steps outlined in this manual your meter will provide years 
of reliable service.

Product Quality

This product has been manufactured in an ISO 9001 facility and has 
been calibrated during the manufacturing process to meet stated product 
specifications. If a certificate of calibration is required please contact the 
nearest authorized REED distributor or authorized Service Center. Please 
note an additional fee for this service will apply.

Safety

•  Never attempt to repair or modify your instrument. Dismantling your 

product, other than for the purpose of replacing batteries, may cause 
damage that will not be covered under the manufacturer's warranty. 
Servicing should only be provided by an authorized service center.

•  Be aware of your surroundings, environment and measurement scope.
•  If the instrument applies to ground resistance testing instead of current 

power frequency wire it will affect the clamps magnetic property and 
the accuracy of measurement.

•  Before turning on the unit, press on the trigger a couple of times to 

confirm it can properly open and close.

•  Do not press the trigger or clamp any wires when turning on the instrument.
•  Only clamp the tested desired object after the display shows "OL Ω".
•  Keep the contact surface of the jaws clean and refrain from using harsh 

cleaning products.

•  When taking measurements the instrument will sporadically "hum".
•  Do not exceed the max measurements.
•  If instrument will not be used for a prolonged amount of time, remove 

the battery.

•  If something is damaged, immediately stop using the instrument.

 

REED Instruments

1-877-849-2127 | [email protected] | www.reedinstruments.com

Summary of Contents for R5700















Reviews: