background image

REDRING AFTER SALES SERVICE

We offer a technical advisory service on the
telephone to contractors and other customers
with problems in the field.

Ring 0870 9000 430 

(Normal Office Hours)

Spare parts can be supplied against any VISA or
Access cards.

Ring 0870 9000 420 

(Normal Office Hours)

Remember to quote the exact type of shower, as
written on the front of the shower and on this
leaflet. It may also be of use to have a note of the
Catalogue Number as stated on the rating plate
inside the shower.

INSTALLATION INSTRUCTIONS

The installation should be done by qualified
personnel and checked by the Electricity Board.

WARNING: DO NOT INSTALL THE SHOWER
IN A ROOM WHERE IT MAY BE SUBJECT TO
FREEZING.

We recommend that the installation is done in the
following sequence :-
A) Fixing the shower to the wall.
B) Plumbing.
C) Electrical connections.

6

Check for cause of high
pressure and remove it.
Blockage on outlet i.e: blocked
spray plate etc. Replace the
pressure relief disc.

e) Water leaks

from burst
pressure
relied valve

Diagram 6

A) Fixing the shower to the wall

The Redring Expressions 570 Pumped
Electric Shower is fitted with a motor and
some mechanical noise can be expected
when in use. The type of wall structure will
affect the noise levels. Solid walls will
provide quieter operation than panel or stud
partition walls.

1. Place the riser rail at the height

recommended in diagram 7b and mark its
position.

2. Position the heater so that the sides of the

unit are vertical and the top is level with, 

or up

to 0.3m (1ft) maximum below the top of
the riser rail.

Choose a flat piece of wall to

avoid the possibility of distorting the backplate
thus making the front cover a poor fit.

3. Adjust the positions to get the most

convenient arrangement taking the following
into account : -

a) The possible need to use the handset

over the sink for hair washing etc.

Diagram 7a

Diagram 7b

3", 8cm min, 33ft (10 m) max,
recommended heights between
bottom of cold water cistern
and top of shower unit.

6'6" (2 m) 

av. height

from top of

riser rail to

base of bath

or cubicle.

Service Valve

Rising Main

1ft (0.3 m) max,

Cold Water

Cistern

Summary of Contents for EXPRESSIONS 570













Reviews: