background image

1. After use in salt water, wash off salt and other contaminants by soaking empty housing 

thoroughly in a bucket of fresh water (lukewarm) for 10 to 20 minutes.

2. Manipulate   all   buttons   and   dials   several   times   to   flush   out   salt   deposits   and   other 

contaminants.

3. Wipe any water off housing with a soft dry cloth.

4. Open Back Cover and remove camera.

5. Remove Lens Port.

6. Using the O-ring Removal Pick, remove O-ringss.

7. Clean O-ring groove and contact surfaces using a clean cotton swab. DO NOT clean 

housing, Back Cover or Lens Port with  volatile  organic  solvents or chemical  cleaning 

agents such as thinner, gasoline, and benzine, etc.

8. Perform O-RING GREASING & MAINTENANCE as instructed below before re-installing. 

O-RING GREASING & MAINTENANCE ( 1)

CAUTION!

 DO NOT use silicone grease other than that provided by Seatool/Recsea.

1. Using the O-ring Removal Pick, remove O-ring.

2. Clean sand, salt, other contaminants and old grease from O-ring.

3. Clean O-ring groove and O-ring Contact Surface using a clean cotton swab.

4. Visually and  physically check O-ring  by running  it  through  finger  tips, feeling  for  cuts,  

cracks  or  any  other  defects  that  may cause  leakage. Such  defects  will  cause  water

leakage, so be sure to replace the O-ring. Be careful not to stretch or pull the O-ring too 

much.

5. Squeeze a rice grain sized bead of silicone grease on your thumb and forefinger. Taking 

care not to pull or stretch the O-ring too much, uniformly spread grease on O-ring. Too 

little grease may cause the O-ring to twist in the groove, possibly causing water leakage.

6. Place O-ring in the appropriate O-ring groove, making sure that it is uniform, not twisted 

or bulging out, possibly causing water leakage. When closing back cover, visually check 

O-ring surface, tracing a finger over the to making sure no hair, lint or other contaminants 

are attached.

IMPORTANT NOTES:

 

When housing and lens ports are not used for long periods, remove O-rings and place in a 

plastic bag to keep the free of dust and other contaminants and store in a place out of 

direct sunlight. Please also be careful of prolonged exposure to direct sunlight during use. 

The O-ring and housing may become deformed, causing water leakage.

 

After extended periods of non-use, soak closed empty housing in lukewarm for half a day. 

Manipulate all buttons and dials several times. Using a soft, dry cloth wipe away water.

CAUTION!

 

The O-ring is an essential part of waterproofing for this housing. Not properly greasing the 

O-ring as directed may cause the O-ring to twist in the O-ring groove, possibly causing 

water leakage.

 

Always perform the above O-ring, O-ring groove and O-ring Contact Surface maintenance 

and greasing every time you open/close the housing.

 

Please pay close attention and make sure the O-rings are not twisted or bulging, free of  

any contaminants (dirt, hair, etc.), and that foreign objects do not obstruct proper closing 

of the housing Back Cover.

 

DO NOT clean the housing with volatile organic solvents or chemical cleaning agents such 

as thinner, gasoline, and benzine, etc.

 

Housing  Back Cover and Port Lens  are manufactured using  hard coat acrylic. When 

cleaning use a clean soft cloth taking care not to scratch it.

8.

Summary of Contents for CWOP-SH2














Reviews: