Record Power BS10 Original Instruction Manual Download Page 3

Page: 3 / 36

THE SYMBOLS AND THEIR MEANINGS SHOWN BELOW MAY BE USED THROUGHOUT THIS MANUAL. PLEASE ENSURE THAT YOU
TAKE THE APPROPRIATE ACTION WHEREVER THE WARNINGS ARE USED.

1. Explanation of Symbols

Mandatory Instructions

Warning

Read and fully understand the instruction manual
before attempting to use the machine.

Indicates an instruction that requires particular attention

Wear protective eyewear

Use respiratory protective equipment

Use suitable protective footwear

Use hearing protection

Use protective work gloves

Indicates a risk of severe personal injury or
damage to the machine

Indicates a risk of severe personal injury
from electrical shock

Risk of personal injury from lifting of heavy items

Indicates a risk of severe personal injury from
airborne objects

Risk of fire

Summary of Contents for BS10





































Search results

Summary of Contents for BS10

Reviews:

Related manuals for BS10

Brands by name

Popular brands

Record Power BS10, Original Instruction Manual

Search results

Summary of Contents for BS10

Reviews:

Related manuals for BS10

Brands by name

Popular brands