background image

2

 

 

 

 
 
 

WARRANTY INFORMATION

 

 

The benefits provided to you under the following warranty are in addition to any other rights and remedies available to 
you under the law.

 

1. Warranty

 

If:

 

(a) 

during the first 15 years from the date of purchase (Firebox Warranty Period), there is a defect in the firebox of the 
Gas Burner; or

 

(b) 

during the first 2 years from the date of purchase (Parts Warranty Period), there is a defect in the gas valves or 
other parts of the Gas Burner,

 

due to improper workmanship or material, Glen Dimplex will replace or repair the Gas Burner without charge. Any 
replacement product is warranted only for the time remaining on the original Firebox Warranty Period or the Parts 
Warranty Period as relevant.

 

2. Registration

 

You must register to receive the benefit of this warranty by completing the warranty registration on our website 
(www.realflame.com.au) or completing and mailing the attached registration card within 30 days of purchase of 
your Gas Burner (or, if the Gas Burner is fitted to a new home, within 30 days of the date of settlement of purchase 
of such new home).

 

3. Exclusions

 

Glen Dimplex is not obliged to replace or repair the Gas Burner under clause 1 if:

 

(a) 

it has been improperly stored, installed, connected, used, operated or repaired, or damaged, abused, tampered 
with, altered (without our written approval), or not maintained in strict accordance with our installation and 
operating instructions; or

 

(b) 

it has been installed in an outdoor setting.

 

4. Limit of Liability

 

The warranty provided under this warranty is limited to replacement or repair of the Gas Burner only, at our option. 
To the extent permitted by law, Glen Dimplex excludes liability for consequential loss or any other loss or damage 
caused to property or persons arising from any cause whatsoever, and damage arising from normal wear and tear.

 

5.  Claiming under the Warranty

 

In order to claim under this warranty you must, within the Firebox Warranty Period or the Parts Warranty Period 
(as relevant), contact Glen Dimplex, providing the original proof of purchase and the details below:

 

 

Supplier Name

  

 

 

Date Of Purchase / settlement of property if new home 

  

 

Model / Serial Number

  

 

This warranty does not cover the cost of claiming under the warranty or transporting the Glen Dimplex Gas Burner to 
and from the supplier.

 

 

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a 
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. 
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure 
does not amount to a major failure.

 

 

If you would like to speak to someone about your Gas Burner or claiming under this warranty, please contact the 
Service Warranty Desk on 1300 554 155.

 

 

Glen Dimplex Australia Pty Ltd ACN 69 118 275 460 

Head Office: 1340 Ferntree Gully Road, Scoresby 3179 

Telephone: (03) 8706 2000 Facsimile: (03) 8706 2001

 

Summary of Contents for Vektor 1100


































Reviews: