manualshive.com logo in svg

READY FORGE OS5, Startup Manual

Share
Download
READY FORGE OS5 Startup Manual Download Page 29

Tap

IMPORT UNLOCK CERTIFICATE

.

Note:

Forge/OS returns to the licensing home screen and shows an active license.

If the license status isn't active, restart these license activation steps.

5

If you need to update Forge/OS

from a USB flash drive, do it through the System Update

screen.

Note:

Contact READY Robotics for an update file. Update files are too large for the

FAT32 file format. Use an exFAT or NTFS formatted USB flash drive with at least 8GB of
storage to download and install the update. Do not use the Forge/OS installation USB
flash drive.

Important:

After you transfer an update file to your USB flash drive, make sure you safely

eject it from your computer. Early removal of the USB flash drive can interrupt data
transfer. If this happens, Forge/OS fails to verify the update file.

9

VERSION 5.0.4

© 2021 COPYRIGHT READY Robotics ALL RIGHTS RESERVED

29

Summary of Contents for FORGE OS5















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands