background image

6. Set the throttle to a high idle. Set the propeller so that it is at the beginning of the
compression stroke.
7. Flip the propeller through compression rapidly. If this is done properly, the engine will
start after several brisk flips of the propeller.
8. After starting, let the engine idle for 30 to 45 seconds. Open and close the throttle
slowly until the engine runs smoothly at idle and at full throttle. Acceleration should also
be smooth. If acceleration is not smooth, adjustments to the carburetor may be
necessary (see Adjustment of the Engine.)
9. If your engine does not start, repeat steps 2-8.

B. Electric Starter Starting

A 12-24V electric starter is recommended to start the RCGF70cc twin.
1. Make sure you use a good quality, lightweight aluminum spinner.
2. Have someone help you hold the airplane while you start it.
3. Switch the ignition to ON, close the choke plate on the carburetor and open the throttle
slightly from the idle position.
4. Use your electric starter to turn the engine over for several seconds, until a popping
sound is heard. This indicates that the engine is firing.
5. Move the choke lever to the open position.
6. Set the throttle to high idle and use your electric starter to turn over the engine until it
starts.
7. After starting, let the engine idle for 30 to 45 seconds. Open and close the throttle
slowly until the engine runs smoothly at idle and at full throttle. Acceleration should also
be smooth. If acceleration is not smooth, adjustments to the carburetor may be
necessary (see Adjustment of the Engine).
8. If your engine does not start, repeat steps 2-7.

Engine Troubleshooting

If your engine fails to start after the preceding starting procedures
please check the following.

Symptom

Diagnosis

Fix

Engine does not fire

Ignition battery

voltage low

Charge or

replace battery

Battery wires faulty

or loose

Replace wires or

Re-connect/check

connections

Faulty spark plug

or not firing

Replace spark plug

or check for spark

Summary of Contents for 70CC-Twin























Reviews: