background image

 

01.12.2017

 

- 10 -

 

raze-cat

 

Technical Specifications 

 

Voltage 

 

 

 

 

 

 

 

230Volt 50Hz 

Connection load   

 

 

 

 

 

750Watt 

Idling speed  

 

 

 

 

 

 

11000min-1 

Belt speed   

 

 

 

 

 

 

360-1000m/min 

Sound pressure level 

 

 

 

 

 

86 dB(A) 

 
 
All  rights  to  make  technical  changes  reserved.  No  legal  claims  may  be 
derived from this user manual. 

 
 

Product warranty note 

 

The above-mentioned product has been checked thoroughly prior to shipping. 
Our warranty covers quality of construction, materials and labour. Damages, 
which have not been recorded at the time of manufacturing, may occur during 
storage and operation. Inasmuch as these are caused by faulty material, or 
labour respectively, we will restore the unit at our expense (with repairs at out 
manufacturing  plant  or  by  delivering  parts),  condition  to  that  is  that  the 
complaint has to have been made within the first twelve months of use, i.e. 
the date of purchase and that the following conditions are met: 
 

1.  When  the  product  has  always  been  connected  to  a  mains  outlet  with 
 

voltage levels that correspond to the ones specified by the  nameplate. 

 

2.  When  the  product  has  only  been  subject  to  normal  usage  and  has 
 

not been used to excess. 

 

3.  When  violent,  improper  or  neglectful  handling  has  not  mechanically 
 

damaged the product. 

 

4.  When the following warranty card accompanies the complaint. 

 

Summary of Contents for ES 2000













Reviews: