Raypak Xfiire 1000B Installation And Operation Manual Download Page 50

Page: 50 / 72

Item

Application

Range

Description

Default

TARGET

H MODE 1, 2, 3

RSET <> SETP

RSET = Outdoor Reset, SETP =Setpoint

SETP

MODE

H MODE 1, 2, 3

1,2,3

Piping and application configuration

SETPOINT

H MODE 1, 2, 3

50°F to 200°F (10°C to 93°C)

Heater target temperature while a heat demand is present for setpoint

operation

180°F (82°C)

OUT START

H MODE 1, 2, 3

35°F to 85°F (2°C to 29°C)

Outdoor starting temperature - outdoor reset

70°F (21°C)

OUT DESIGN

H MODE 1, 2, 3

-60°F to 45°F (-51°C to 7°C)

Outdoor design temperature - outdoor reset

10°F (-12°C)

Boil START

H MODE 1, 2, 3

35°F to 150°F (2°C to 66°C)

Starting heater target temp when the outdoor temperature is at outdoor

start outdoor reset

70°F (21°C)

Boil DESIGN

H MODE 1, 2, 3

70°F to 200°F (21°C to 93°C)

Design heater target temperature when the outdoor temperature is at

outdoor design outdoor reset

180°F (82°C)

TARGET MAX

H MODE 1, 2, 3

100°F (38°C) to PIM value*

Maximum target system temperature

200°F (93°C)

TARGET MIN

H MODE 1, 2, 3

OFF, 50°F to 190°F (10°C to

88°C)

Minimum target system temperature

50°F (10°C)

TARGET DIFF

H MODE 1, 2, 3

2°F to 42°F (1°C to 23.3°C)

Differential for target system temperature

10°F (5.6°C)

IND SENSOR

H MODE 1, 2, 3

OFF <> ON

Selects whether a DHW sensor is used for indirect DHW tank

OFF

IND SETP

H MODE 2, 3

OFF, 50°F (10°C) to 180°F

(82°C)

Target Indirect DHW Temperature, requires IND SENSOR = ON

140°F (60°C)

DHW DIFF

H MODE 2, 3

2°F to 10°F (1°C to 5.6°C)

Target indirect DHW tank temp, requires IND SENSOR = ON

6°F (3.4°C)

GLYCOL

IDLE only

0% - 50%

Glycol concentration

50%

Delta T Offset

H MODE 1,2,3

2°F to 15°F (1°C to 8.5°C)

DT Offset (Flow Warning threshold)

10°F

Isol Valve ON/OFF

IDLE only

0:CLOSE, 1:OPEN

Manual Open / Close of ISOL Valve

1, OPEN

VENT MATERIAL

IDLE only

PVC, CPVC, PPS, SS

Defines VENT Piping material. To update value unit must be in IDLE

status. (Tap 6 times on setting label to enable SET button)

PVC

VENT DIFF

IDLE only

1°F to 20°F (1°C to 11.2°C)

Substractive differential of VENT Temperature. This value sets the

threshold for VENT protection to be active

10°F (5.6°C)

VENT RATE

IDLE only

MIN Firing Rate to 80%

Forced firing rate when VENT protection is present

50%

# ISOL Valves

Open

Cascade Only

1, 2, 3, 4

Number of ISOL Valves open in a cascade configuration

Cascade Type

Cascade Only

SEQ, PAR

Cascade operation type

SEQ

Cascade MIN Flow

Offset

Cascade Only

-25 to 15 GPM

Overrides MIN flow condition for next unit in cascade to allow next unit to

be called to fire sooner or later.

Flow Override

IDLE only

0,MIN % to 80%

Overrides MIN Flow condition for ignition sequence, setting expires in

24hrs.

IND SUPPLY

H MODE 2, 3

OFF, 50°F (10°C) to PIM

value*

Target heater temperature for the DHW heat exchanger during indirect

DHW operation, requires IND SENSOR = OFF

180°F (82°C)

DHW PRIORITY

H MODE 2

OFF <> ON

Selects whether or not Indirect DHW priority is active during indirect DHW

operation

OFF

PRI OVR

H MODE 2, 3

Au, 0:10hr to 2:00hr

Sets the length of the indirect DHW priority override time

1:00hr

SYS PURGE

All

OFF, 0:20min to 20:00min

Sets the length of the system pump post purge

20 seconds

MIX TYPE

H MIX

H (VALVE, PUMP, PLNT)

WH (1 <> 2)

Selects the type of control depending on pipe configuration for CWP

H VALVE

MIX TARGET

H MIX

50°F to 140°F (10°C to 60°C)

Inlet Target Temperature

120°F (49°C)

MIX LOCK

H MIX

OFF <> ON

The equipment will trigger a warning when “MIX Target” is not reached

within 7 minutes. MIX LOCK = ON; Alarm and lockout, MIX LOCK = OFF;

Alarm only

OFF

MIX TRIM

H MIX

-5 to 5

This adjustment is for various types and sizes of units as well as various

actuator motor speeds and types supplied by Raypak

MIX SPEED

H MIX

SLOW <> MED <> FAST

This setting defines speed of response

MED

MIX INV

H MIX

OFF <> ON

Relates to the use of spring return actuators with a proportional valve

OFF

WWSD

H MODE 1, 2, 3

40°F to 100°F (4°C to 38°C)

The system warm weather shutdown temperature outdoor reset, requires

TARGET = RSET

70°F (21°C)

UNITS

All

deg F <> deg C

Show units using icons in display

deg F

MODBUS

All

OFF <> MNTR <>TEMP <>

RATE

ModBus Operating Mode: Off, Monitor, Temp Control, Rate Control

MNTR

ADDRESS

All

1 to 247

ModBus slave address

DATA TYPE

All

RTU <> ASCI

Modbus data type

RTU

BAUD RATE

All

2400 <> 9600 <> 19K2

<>57K6 <> 115K

19K2

PARITY

All

NONE <> EVEN <> ODD

EVEN

* Maximum operator dial setting.

Table W.

Setup/Adjust Menus

Summary of Contents for Xfiire 1000B









































































Search results

Summary of Contents for Xfiire 1000B

Reviews:

Related manuals for Xfiire 1000B

Brands by name

Popular brands

Raypak Xfiire 1000B, Installation And Operation Manual

Search results

Summary of Contents for Xfiire 1000B

Reviews:

Related manuals for Xfiire 1000B

Brands by name

Popular brands