Raynor Premium series 8500RGD Prodigy II Owner'S Manual Download | Manualshive

Page: 35 / 36

background image

35

Security

✚

2.0™ Wireless Door Control:

Push bar, light feature and
auxiliary button. Includes
battery.

Alternate Mounting Kit:

This kit allows model
8500RGD to be mounted
below the torsion bar in the
case where the torsion bar
is not round or the normal
mounting area is obstructed.

Alternate Power System:

Model 580LG Alternate
Power Supply may be
installed if an outlet is not
located near the garage
door opener.

Garage and Gate Monitor:

Monitor open/closed
status for up to 4 MyQ

®

compatible garage door
openers or gate operators
and close them from anywhere in the home.

Remote Light:

Enables homeowner
to turn on a work
light from their car
with their garage door
opener remote or from
anywhere in their home
with an additional Raynor

®

Security

✚

®

remote.

Remote Light Control:

Automatically control your lights
using your garage door opener,
a SECURITY

✚

2.0™ remote

control or a MyQ

®

Internet

Gateway. Plugs into any interior outlet.

Remote Light Switch:

Automatically control your lights
using your garage door opener,
a SECURITY

✚

2.0™ remote

control or a MyQ

®

Internet

Gateway. Simply replaces your current
wired wall switch.

3-Button Remote Control:

Includes visor clip.

MyQ

®

Internet Gateway:

Internet enabled
accessory which connects
to the computer and
allows you to monitor and
control garage door openers and lighting
accessories enabled by MyQ

®

technology.

Surge Protector:

The Garage Door Opener Surge
Protector is designed to protect
Raynor

®

garage door openers

against damage from lightning
and power surges. Easy to install.

MAX Wireless Keyless Entry:

For use outside of the
home to enable access to
the garage using a 4-digit
PIN.

Accessories

893RGX

828LG

990LM

877MGX

829LM

41A7773-1

825LM

823LM

380LM

895RGX

3-Button Remote Control:

Includes visor clip.

480LM

580LG

Extension Brackets:

(Optional) For safety
reversing sensor installation
onto the wall or ﬂ oor.

41A5281-1

Battery Backup:

Provides backup power
to the garage door
opener.

475RGD

MAX ACCESSORIES

Compatible with Raynor

®

garage door

openers manufactured since 1993.

MyQ

®

ACCESSORIES

STANDARD ACCESSORIES

«
...
33
34
35
36
»

Summary of Contents for Premium series 8500RGD Prodigy II





































Reviews:

No comments

Related manuals for Premium series 8500RGD Prodigy II

Brand: tousek Pages: 36

Brand: Hamilton Beach Pages: 8

Brand: Emerson Pages: 5

Brand: Xtreme Garage Pages: 2

Brand: tau Pages: 52

Brand: V2 Pages: 100

Brand: DACE Pages: 22

Telcoma EVO 2000

Brand: SAFE HOME Pages: 14

Brand: Garaga Pages: 2

Brand: Accessmatic Pages: 22

ULTRA 3595RGDS 3/4 HP

Brand: Raynor Pages: 36

Brand: Chamberlain Pages: 25

UNV-Light LO TB

Brand: LOBAS Pages: 56

Brand: SEA USA Pages: 12

Brand: G-Force Pages: 20

Brand: Viking Access Systems Pages: 50

Brand: CAME Pages: 80

Brand: Witura Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands