4
To prevent possible SEVERE INJURY or DEATH:
• Install a LiftMaster Monitored Entrapment Protection (LMEP)
device.
• NEVER permit children to operate or play with door control
push buttons or remote controls.
• Activate door ONLY when it can be seen clearly, is properly
adjusted and there are no obstructions to door travel.
• ALWAYS keep door in sight until completely closed. NEVER
permit anyone to cross the path of closing door.
BASIC PROGRAMMING
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
23
4
5
6
7
ST
OP
CLOSE
OPEN
R27
AUX
ANT
^^^^
AUX
ANT
AUX ANT
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
23
4
5
6
7
ST
OP
CLOSE
OPEN
SINGLE BUTTON REMOTE CONTROL
1
Press and release
the LEARN button
(LED will light).
2
Repeat steps 1 and 2 for additional remote controls.
REMOTE CONTROLS
Built in 315 MHz radio receiver permits as many as 20 Security
✚
®
remote controls or dip switch remote controls in any combination.
Press and hold the button on the remote control until the LED
fl ashes rapidly, then release to complete programming (LED
will go out).
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
23
4
5
6
7
ST
OP
CLOSE
OPEN
R27
AUX
ANT
^^^^
AUX
ANT
AUX ANT
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
23
4
5
6
7
ST
OP
CLOSE
OPEN
TO ERASE ALL REMOTE CONTROLS
1
Press and hold the
LEARN button (over
5 seconds) until the
LED goes out. All
programmed remote
controls will be
erased.
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
23
4
5
6
7
ST
OP
CLOSE
OPEN
R27
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
23
4
5
6
7
ST
OP
CLOSE
OPEN
R27
AUX
ANT
^^^^
AUX
ANT
AUX ANT
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
23
4
5
6
7
ST
OP
CLOSE
O
PEN
3-BUTTON REMOTE CONTROL TO OPERATE AS A WIRELESS 3-BUTTON CONTROL STATION
NOTE:
The feature will use 3 of the 20 memory channels in the operator.
1
2
3
Press and hold
the LEARN button
(LED will light).
Press the desired
button on the logic
board (OPEN,
CLOSE or STOP).
Release both
buttons.
Press and hold the desired button of the remote
control until LED fl ashes rapidly, then release.
Repeat steps 1 through 3 to program additional buttons.
ATTENTION
AVERTISSEMENT
AVERTISSEMENT
AVERTISSEMENT
WARNING
WARNING
CAUTION
WARNING
WARNING
PRECAUCIÓN
ADVERTENCIA
ADVERTENCIA
ADVERTENCIA
RADIO OPERATION
MODE
OPEN
CLOSE
STOP
REVERSE WHILE
CLOSING
TTC RESET
B2
X
X
X
X
B2 with TTC
X
X (3-button remote)
X
X
X when open
C2
X
X
X
Summary of Contents for MT5011UCHB
Page 10: ...10 OPERATOR NOTES...