Raynor 1280RGD Owner'S Manual Download Page 33

Page: 33 / 36

NOTICE

CEILING MOUNT O

NLY

LOCK

LIGHT

RAIL GREASE

NO. 83A4

Installation Parts

REPAIR PARTS

Rail Assembly Parts

KEY

PART

NO. NO.

DESCRIPTION

1A995

Master link kit

41A3588-1

Belt pulley bracket

41B3869-1

Complete trolley assembly

109B33

Trolley clip

183B99

One-piece T-rail

41A3589-12

Full belt assembly

41B4103

Tensioner assembly

83A4

Rail grease

KEY

PART

NO.

DESCRIPTION

41A45276-15

Multi-function door control panel

41A5056-3RGD

3-channel remote control housing
(no circuit board)

10A20

3V2032 Lithium battery

29B137

Remote control visor clip

41A2828

Manual rope & handle assy.

217A238

2-Conductor bell wire, white &
white/red

41A5047-1

Door bracket w clevis pin & fastener

41A4353-1

Header bracket w/clevis pin &
fastener

41A5034

Safety sensor kit (receiving and
sending eyes) with 3' 2-conductor
bell wire attached

178B34

Straight door arm section

178B35

Curved door arm section

41A5266-1

Safety sensor brackets (2)

Not shown

41A2770-5

Installation hardware bag
(includes hardware listed on page 5).

114A2374

Owner's manual

Summary of Contents for 1280RGD





































Search results

Summary of Contents for 1280RGD

Reviews:

Related manuals for 1280RGD

Brands by name

Popular brands

Raynor 1280RGD, Owner'S Manual

Search results

Summary of Contents for 1280RGD

Reviews:

Related manuals for 1280RGD

Brands by name

Popular brands