Raymarine AIS500 User Manual Download Page 3

 

LD2342 V1.4 Page 3 of 22

SRT Marine Technology 

 

User guide 

SRT-MTB

©

 proAIS Application 

 

GENERAL WARNINGS 

All marine Automatic Identification System (AIS) units utilise a satellite based system such as the Global Positioning Satellite 
(GPS) network or the Global Navigation Satellite System (GLONASS) network to determine position. The accuracy of these 
networks is variable and is affected by factors such as the antenna positioning, how many satellites are used to determine a 
position and how long satellite information has been received for. It is desirable wherever possible therefore to verify both your 
vessels AIS derived position data and other vessels AIS derived position data with visual or radar based observations.  

The proAIS application is intended for use as an installation and configuration tool. 

The application is not a navigation tool 

and should not be used as such.

 

 

LICENSING 

IMPORTANT: In most countries the operation of an AIS unit is included under the vessels marine VHF licence provisions. The 
vessel on to which the AIS unit is to installed must therefore possess a current VHF radiotelephone licence which lists the AIS 
system and the vessel Call Sign and MMSI number. Please contact the relevant authority in your country for more information. 
In accordance with a policy of continual development and product improvement the AIS500 hardware and software may be 
upgraded from time to time and future versions of the AIS500 may therefore not correspond exactly with this manual. When 
necessary upgrades to the product will be accompanied by updates or addenda to this manual. Please take time to read this 
manual carefully and to understand its contents fully so that you can install and operate your AIS system correctly. 
Information contained in this manual is liable to change without notice. Software Radio Technology plc disclaims any liability for 
consequences arising from omissions or inaccuracies in this manual and any other documentation provided with this product. 
 

DISCLAIMER 

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR 
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR 
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF 
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, 
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY 
WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 
 
 
This software uses components and source code developed by other companies or groups. 
 
Microsoft .Net Framework V2.0: 
 

Copyright © 2005 Microsoft Corporation 

 
ZedGraph Graphing component dll (http://zedgraph.org): 
 

Provided under the GNU Lesser General Public License 

 
 
 

 

All trademarks mentioned in this document are the property of their respective owners. 
Copyright © 2009 

Summary of Contents for AIS500
























Reviews: