background image

20                                                                                                                                                                           Raymarine 37STV Satellite TV System

2.  Connect the RF1 cable to ‘

ANTENNA

’ on the rear of the 

ACU.

3.  Connect the RF2 cable to ‘

Lo/Hor

’ on the multiswitch.

4.  Connect an RF cable from ‘

RECEIVER

’ on the rear of the 

ACU to ‘

Lo/Ver

’ on the multiswitch.

5.  For each output required, connect an RF cable from an ‘

OUT

’ 

connector of the multiswitch to the ‘

LNB

’ or ‘

ANT

’ of the 

individual IRD units.

Note:   If you prefer watching programmes in the high band, 

repeat Steps 3 and 4, but connect the RF cables to ‘Hi/
Hor’ or ‘Hi/Ver’.

Connecting the system to a GPS

For improved satellite tracking, you can connect your satellite TV 
system directly to your boat’s NMEA 0183 GPS system. To do 
this you will need two lengths of cable suitable for connecting to 
your GPS system and the green 2-way ACU GPS connector 
supplied with your 37STV Satellite TV System.

To connect the system to a GPS:

1.  Strip back the insulation of each cable and connect a cable to 

each terminal of the 2-way connector.

2.  Tighten the locking screws.

3.  Connect the cable from the 

+ve 

terminal of the ACU GPS 

connector to the NMEA 

OUT

 wire of the boat’s GPS system. 

4.  Connect the cable from the 

-ve

 terminal of the ACU GPS 

connector to the 

ground wire 

of the boat’s GPS system.

5.  Refit the ACU GPS connector to the rear of the ACU.

81304_2.book  Page 20  Thursday, March 26, 2009  3:59 PM

Summary of Contents for 37STV



































































Reviews: