Raycus RFL-C1000 User Manual Download Page 40

Page: 40 / 44

Wuhan Raycus Fiber Laser Technologies Co., Ltd

ser Guide of 1000W CW laser

Raycus User Guide | Common Alarms and solutions

Table12 Error instructions and possible solutions

Alarm message

Error instructions and possible solutions

System Timer

Alarm

Instruction:

Internal clock abnormal

Solutions:

When this alarm occurs, please contact Raycus directly

Laser On Button

Alarm

Instruction:

This alarm occurs when the light exit button on the front panel

of the laser has been pressed before powering on

Solutions:

When this alarm occurs, please power off the laser and make

the light enable button pop up, and then power on the laser

again to cancel the alarm. If the alarm continues to occur,

please contact Raycus.

Inter Lock Alarm

Instruction:

Occurs when the laser InterLock is disconnected

Solutions:

Short the InterLock pins. If this error continues to occur, please

contact Raycus.

Current Driver

Alarm

Instruction:

Internal constant current driver is error

Solutions:

Restart the Device. If this error continues to occur, please

contact Raycus.

Summary of Contents for RFL-C1000













































Search results

Summary of Contents for RFL-C1000

Reviews:

Related manuals for RFL-C1000

Brands by name

Popular brands

Raycus RFL-C1000, User Manual

Search results

Summary of Contents for RFL-C1000

Reviews:

Related manuals for RFL-C1000

Brands by name

Popular brands