Raycus RFL-C1000 User Manual Download Page 41

Page: 41 / 44

Wuhan Raycus Fiber Laser Technologies Co., Ltd

ser Guide of 1000W CW laser

Raycus User Guide | Common Alarms and solutions

Laser OutAlarm

Instruction:

The laser will get this alarm when it can not detect any laser

light signal. Laser out alarm occurs only when the laser is

emitting light

Solutions:

Restart the Device. If this error continues to occur, please

contact Raycus.

Laser Power Alarm

Instruction:

The alarm is generated when the emission of the laser cannot

reach the set value. Power alarm occurs only when the laser is

emitting light.

Solutions:

Restart the Device. If this error continues to occur, please

contact Raycus.

ACDC1 Alarm

Instruction:

AC/DC1 Alarm. Laser power supply out of work or sudden

power disconnect of the power supply system may cause the

alarm

Solutions:

Check whether the input AC voltage is normal. Restart the

laser to try when it is normal. If the alarm continues to occur,

please contact Raycus.

ACDC2 Alarm

Instruction:

AC/DC2 Alarm. Overcurrent or overvoltage inside the device

may cause this error.

Solutions:

Check whether the input AC voltage is normal. Restart the

laser to try when it is normal. If the alarm continues to occur,

please contact Raycus.

Summary of Contents for RFL-C1000













































Search results

Summary of Contents for RFL-C1000

Reviews:

Related manuals for RFL-C1000

Brands by name

Popular brands

Raycus RFL-C1000, User Manual

Search results

Summary of Contents for RFL-C1000

Reviews:

Related manuals for RFL-C1000

Brands by name

Popular brands