manualshive.com logo in svg

Raycus RFL-C Series, User Manual, Page: 8 / 47

Share
Download
Raycus RFL-C Series User Manual Download Page 8

Wuhan Raycus Fiber Laser Technologies Co., Ltd.

 

User Guide 100W

~

750W Ver: 1.0                                                                                      

                             

6

 

 

2

 

Product Description 

2.1

 

Features 

Your Raycus CW fiber laser is designed for industrial and scientific research applications with 

high pump conversion efficiency, low power consumption and excellent beam quality. It is 

compact and ready to use. It can be used as a stand-alone unit or easily inserted into user’s 

apparatus. 

Main Features:

 

 

High beam quality   

 

Fiber delivery 

 

Reliable, long lifetime 

 

Maintenance free operation 

 

High wall-plug efficiency 

 

Convenient control interface 

 

Fast modulation 

Applications: 

 

Cutting   

 

Welding 

 

Scientific research 

2.2

 

Model Configuration 

The RFL-C series include 100W, 200W, 300W, 400W, 500W, 600W, 700W and 750W 

continuous fiber laser, and the model designation codes are illustrated in the following table: 

Table 2: Model Names and Designation Codes 

Summary of Contents for RFL-C Series
















































Reviews:

No comments