manualshive.com logo in svg

Raycus RFL-C Series, User Manual, Page: 34 / 47

Share
Download
Raycus RFL-C Series User Manual Download Page 34

Wuhan Raycus Fiber Laser Technologies Co., Ltd.

 

User Guide 100W

~

750W Ver: 1.0                                                                                      

                             

21

 

Error 1 to Error 5 is different errors like output power error, over temperature error, etc. Only the 

times of occurrence is displayed. Follow the instruction to press ‘U’ to enter user interface (UI). 

If you fail to do this, the system will enter RS-232 mode with CTRL-INTERFACE disconnected. 

In this condition, there is no other ways for you to enter hyper terminal UI but to turn off the 

laser and start again, then go through the procedures above, press ‘U’ when instructed. Notice 

that ‘U’ must be capital letter. 

After you enter the UI, press ‘Enter’, and the following options will be displayed: 

You have entered UI, press ‘Enter’……………………… 

Welcome to use Raycus fiber laser 

Please choose the operation mode: 

1-> CW mode 

2->Pulse mode 

3->CW mode with remote modulation 

4->Pulse mode with remote modulation 

5->Clear errors 

6->Save system configurations 

7->Return 

You can enter the operation mode by pressing corresponding number on the keyboard. 

 

CW mode 

Press ‘1’ in the mode selection page, you will enter ‘CW mode’. In this mode, the laser emission 

is continuous, so just one parameter needs to be set-percentage of output power. 

The present operation mode is CW mode 

Please set percentage of output power (MIN=0, MAX=100), press ‘Enter’ to confirm: 

Then type a number between 0 and 100, with minimum increment of 1, then press ‘Enter’. 

For example, type ‘20’ and enter, the output power will be set to approximate 20%. 

Please set percentage of output power (MIN=0, MAX=100), press ‘Enter’ to confirm:20 

Summary of Contents for RFL-C Series
















































Reviews:

No comments