RG74T-R Operator · Service · Maintenance
800.392.2686
15
Inspect all lines and hoses for wear or for deterioration. The
hoses must be properly routed. The lines and the hoses
must have adequate support and secure clamps. Tighten
all connections to the recommended torque. Leaks can
cause fires.
Use caution when you are refueling a machine. Do not smoke
while you are refueling a machine. Do not refuel a machine
near open flames or sparks. Always stop the engine before
refueling. Fill the fuel tank outdoors.
Gases from a battery can explode. Keep any open flames
or sparks away from the top of a battery. Do not smoke in
battery charging areas.
Never check the battery charge by placing a metal object
across the terminal posts. Use a voltmeter or a hydrometer.
Improper jumper cable connections can cause an explosion
that can result in injury. Refer to the Operation Section of
this manual for specific instructions.
Do not charge a frozen battery. This may cause an explosion.
Fire Extinguisher
Make sure that a fire extinguisher is available. Be familiar
with the operation of the fire extinguisher. Inspect the fire
extinguisher and service the fire extinguisher regularly. Obey
the recommendations on the instruction plate.
Fire Extinguisher Location
Make sure that a fire extinguisher is on the machine. Make sure
that you are familiar with the operation of the fire extinguisher.
Inspect the fire extinguisher and service the fire extinguisher.
Obey the recommendations on the instruction plate.
Mount the fire extinguisher in an easily accessible place on
the machine, for crawlers mount on the left side of the cab
behind the seat. Consult your Rayco dealer for the proper
procedure of mounting the fire extinguisher.
Ether Starting Fluid
Ether is flammable and poisonous.
Use ether in well ventilated areas. Do not smoke while you
are replacing an ether cylinder or while you are using an
ether spray.
Do not store ether cylinders in living areas or in the operator
compartment of a machine. Do not store ether cylinders in
direct sunlight or in temperatures above 49 °C (120 °F). Keep
ether cylinders away from open flames or sparks.
Dispose of used ether cylinders properly. Do not puncture an
ether cylinder. Keep ether cylinders away from unauthorized
personnel.
Do not spray ether into an engine if the machine is equipped
with a thermal starting aid for cold weather starting
Lines, Tubes and Hoses
Do not bend high pressure lines. Do not strike high pressure
lines. Do not install any lines that are bent or damaged.
Repair any lines that are loose or damaged. Leaks can
cause fires. Consult your Rayco dealer for repair or for
replacement parts.
Check lines, tubes and hoses carefully. Do not use your bare
hand to check for leaks. Use a board or cardboard to check
for leaks. Tighten all connections to the recommended torque.
Replace the parts if any of the following conditions are present:
• End fittings are damaged or leaking
• Outer coverings are chafed or cut.
• Wires are exposed.
• Outer coverings are ballooning.
• Flexible part of the hoses are kinked.
• Outer covers have embedded armoring.
• End fittings are displaced. Make sure that all clamps,
guards, and heat shields are installed correctly. During
machine operation, this will help to prevent vibration,
rubbing against other parts, and excessive hear.
Electrical Storm Injury Prevention
When lightning is striking in the vicinity of the machine, the
operator should never attempt to operate the machine. If you
are on the ground during an electrical storm, stay away from
the vicinity of the machine!
Safety
Summary of Contents for RG74T-R
