background image

The Rayburn Heatranger 368K is a combined
cooker/boiler appliance, providing central heating,
domestic hot water and cooking facilities.

It is available with a vertical flue outlet only. The cooker
burner operates on natural draught. The boiler burner is
fan assisted in conjunction with full sequential controls.

The boiler is designed for use with open vented water
systems only. Operating with gravity D.H.W. via the

cooker burner (for Summer use) or a modified Fully
Pumped Central Heating System as detailed in these
instructions.

NOTE: SMOKE/SMELL EMITTED DURING INITIAL
USAGE

Some parts of the cooker have been coated with a light
covering of protective oil. During initial operation of the
cooker, this may cause smoke/smell to be emitted and is
normal and not a fault with the appliance, it is therefore
advisable to open doors and or windows to allow for
ventilation. Lift the insulating lids to prevent staining the
linings.

Boiler Water Connections

Flow (one) 

Rp 1 (1in BSP int)

Return (one) 

Rp 1 (1in BSP int)

Both connections are located towards the rear edge of
the appliance L.H. side panel.

Oil Valve Inlet 

Rp 1¼4 (1¼4in BSP int)

Flue Outlet Dia. 

127mm

Electrical Supply 

240V ~ 50Hz 5 amp Fused

Weight Capacity 

12.5 litres

of Boiler 

Weight of Appliance 

348kg

Appliance Overall

Height: 975mm

Dimensions 

Width:  997mm
Depth: 647mm

FUEL - 
COMMERCIAL KEROSENE current issue to BS.
2869: Class C2 suitable for vapourising burners

Installation

and

Servicing

Instructions

4.5 – 4.75

13.0 – 13.5

42.50 – 44.75

51.0 – 53.5

0.85

2,900

26.6

90,900

31.97

110,100

18.4

62,900

20.0

68,530

2.5

8,530

Heat Input

cc/minute

Heat Output

Water

Oil Input

Rate

kW

Btu/h

2.9

9,870

8.2

28,000

Cooker Only

LOW

Cooker Only

HIGH

Cooker LOW

Boiler ON

Cooker HIGH

Boiler ON

kW

Btu/h

IMPORTANT: IN ORDER TO MAINTAIN OPTIMUM PERFORMANCE FROM THIS APPLIANCE, IT IS ESSENTIAL THAT THE
INITIAL COMMISSIONING IS UNDERTAKEN BY SELECTED, TRAINED INSTALLATION/SERVICING ENGINEERS. YOUR
RAYBURN STOCKIST WILL PROVIDE ADVISE ON THE LOCATION OF THE NEAREST INSTALLING ENGINEER, AND WE
RECOMMEND YOU CONTRACT OUT THE PERIODICAL SERVICING OF THE APPLIANCE TO THIS ENGINEER.

INTRODUCTION

11/06 EINS 511322 

[email protected]

Heatranger 368K

Consumer Protection

As responsible manufacturers we take care to make sure that our
products are designed and constructed to meet the required safety
standards when properly installed and used.

IMPORTANT NOTICE: PLEASE READ THE ACCOMPANYING
WARRANTY.

Any alteration that is not approved by Aga could invalidate the
approval of the appliance, operation of the warranty and could affect
your statutory rights.

Important

This appliance may contain some of the materials that are indicated
It is the Users/Installers responsibility to ensure that the necessary
personal protective clothing is worn when handling where 

applicable, the pertinent parts that contain any of the listed materials
that could be interpreted as being injurious to health and safety, see
below for information.

Firebricks, Fuel beds, Artificial Fuels - 

when handling use

disposable gloves.

Fire cement - 

when handling use disposable gloves.

Glues and Sealants 

- exercise caution - if these are still in liquid form

use face mask and disposable gloves.

Glass Yarn, Mineral Wool, Insulation Pads, Ceramic Fibre,
Kerosene/Gas Oil -

may be harmful if inhaled. May be irritating to

skin, eyes, nose and throat.  When handling avoid contact with skin
or eyes. Use disposable gloves, face-masks and eye protection. After
handling wash hands and other exposed parts.  When disposing of
the product, reduce dust with water spray, ensure that parts are
securely wrapped.

Summary of Contents for Heatranger 368K


























Reviews: