background image

REMEMBER: BE CAREFUL OF THE HOT APPLIANCE.

DO NOT USE A STEAM CLEANER TO CLEAN THIS
COOKER.

To keep the vitreous enamelled surface bright and clean,
wipe over daily with a soapy damp cloth, followed by a
clean dry duster. If milk, fruit juice or anything containing
acid is spilt on the top plate or down the cooker, be sure to
wipe it immediately or the vitreous enamel may be
permanently discoloured. Keep a damp cloth handy, while
cooking to wipe up spills as they occur, so they do not
harden and become more difficult to remove later. If spills
do become baked on a cream cleanser can be used. For
stubborn deposits a soap impregnated pad can be
carefully used on the vitreous enamel.
In the main oven, spills and fat splashes are carbonised at
high temperatures; occasionally brush out with a stiff
brush. The oven door can be removed for cleaning - 

do

not 

immerse in water, and shelves can be soaked and

cleaned with a cream cleanser.
Both insulating covers should be raised and allowed to
cool before cleaning with a soapy damp cloth. Use a wire
brush to keep the cast iron hotplate clean.
General cleaning is best carried out when the Rayburn is
cool.

IMPORTANT:

Aga recommend Vitreous Enamel Association approved
cleaners for cleaning the vitreous enamelled surfaces of
this product.

But they are unsuitable for use on chrome and stainless
steel components, including the hand-rails and their
brackets.

The insulating covers should be cleaned regularly with a
NON-ABRASIVE mild detergent, applied with a soft
(coarse free) cloth and lightly polished up afterwards with a
soft (coarse free) duster or tissue, to bring it back to its
original lustre.

Bi-annual Servicing

With normal use a cooker annual flueway clean and burner
maintenance should be carried out at 6 monthly intervals.
The cooker oil valve control knob should be turned 

OFF

by

the User the night before the day of the servicing so that
the appliance will have cooled down by the following
morning.

A HOT APPLIANCE CANNOT BE SERVICED.

Your Rayburn stockist will provide advice on obtaining the
nearest selected Servicing Engineer, where we
recommend you contract out the periodical servicing of the
appliance.

4

CLEANING

BI-ANNUAL SERVICING

Summary of Contents for Cookmaster 208K





























Reviews: