Raven MPV-7100 Owners And Operation Manual Download Page 8

Page: 8 / 52

Install the Steering Wheel

Locate the steering wheel and steering wheel hardware packet.

Ensure that the front wheels are pointing forward and slide

steering wheel onto the steering spindle, making sure that the

steering wheel spoke between the hub connectors is centered

and pointing towards the operator.

Slide the 21mm lock washer onto the steering spindle.

Install the 21mm nut to secure the steering wheel.

Install the Seat

Place the seat on the unit and line up the holes on the seat

hinge with those on the unit.

Install the two M8 x 25mm flanged shoulder bolts and lock-nuts

in the seat hardware pack and hand tighten.

Lift the seat. Do not remove the black foam inside the seat

springs. Tighten with a 12mm wrench for the nuts and a 13mm

wrench for the bolts.

Connect the safety switch harness to the bottom of the seat.

Lower the seat into place.

List of Parts

RAVEN MPV-7100/7100S OWNER’S MANUAL

I NI T I AL SET -UP

You will need the following tools to assemble the MPV:

•   12mm wrench
•   13mm wrench
•   21mm socket & ratchet wrench
•   adjustable wrench

ntroduCtIon

St e e r i n g Wh e e l

2 1m m Nu t

M8 B o l t

13 m m Wr e n c h

Sw i t c h H a r n e s s

Se a t Pa n

2 1m m Lo c k Wa s h e r

M8 Nu t

St e e r i n g

Wh e e l

Se a t

T o w B a r

3 0A

F u s e s

Se a t H i n g e

12 m m Wr e n c h

Se a t H a r n e s s

Pl u g

2 1m m Wa s h e r

Se a t Pa n

Summary of Contents for MPV-7100





















































Search results

Summary of Contents for MPV-7100

Reviews:

Related manuals for MPV-7100

Brands by name

Popular brands

Raven MPV-7100, Owners And Operation Manual

Search results

Summary of Contents for MPV-7100

Reviews:

Related manuals for MPV-7100

Brands by name

Popular brands