background image

Seat Adjustment

While seated, pull up on the seat adjustment lever and slide 

the seat forward or backward to adjust the position.

Removing the Tailgate

a. 

Lower the tailgate all the way down.

b. 

Press down on the tailgate at the hinge points to remove.

c. 

Reverse these steps for reassembly.

Gear Selection

a. 

Low gear is towards you, high gear is away.

b. 

Pull down and move the gear selection arm into the desired 

gear slot. 

c. 

If the lever appears to be stuck, roll the rear tire slightly with 

your hand while adjusting lever.

WWW. RAVENAMERI C A. C OM

F

eatures

WARNING!

Use caution when operating at high speed.

MPV Speed Management

The MPV is equipped with a high and low gear. The gear 

selector is located on the right side of the MPV to the left 

of the discharge chute. High gear should be used mainly 

for transport and is capable of reaching speeds up to 17 

miles per hour. Low gear focuses on power and torque and 

should be used for activities requiring more power and for 

mowing. The MPV is capable of reaching a speed of up to 

6 miles per hour in low gear. 

NOTE: 

The MPV must be in low gear to operate the mowing 

deck attachment. 

Seat Adjustment Lever 

The MPV seat is adjustable to provide a more comfortable 

ride while using the MPV.

 

17

H i n g e  Po i n t s

H i n g e  Po i n t

Se a t  Ad j u s t m e n t

Le v e r

Lo w  G e a r  Sl o t

H i g h  G e a r  Sl o t

Sh i f t  Le v e r

Summary of Contents for MPV-7100





















































Reviews: