background image

IP Deskset 47816A-700/710 Manual 

V A.1.0 

 

10 | 

P a g e

 

 

IP Deskset Controls 

10.1 The IP Deskset comes with an AC adapter that plugs into the rear of the unit. 
10.2 Also located on the rear of the unit is a network port. 
10.3 The dash 700 model comes with a supplied Gooseneck style microphone that plugs into the XLR 
connector on the top of the unit. The dash 710 unit comes with a built-in microphone and does not need 
installation. 
10.4 The volume knob is used to select the level of the audio output and when in menu mode it is used 
to scroll through the menu. 
10.5 The A button is used to make calls. Press the A button once and use the keypad to enter the desired 
number (note that * and # can create different characters each time they are pressed). After the 
number, has been entered press the A button again to make the call. 
10.6 The A button can also be used to make calls using the directory. Select the A button and scroll 
through the directory by turning the volume knob. Once you have selected a number press the A button 
again to make the call. 
10.7 By pressing the B button it will bring up the users help guide. 
10.8 Pressing C will cancel the call. 
10.9 The D button will disconnect the current call. 
10.1.0 When in call use the push and hold the Push to Talk button to talk to the person on the other 
end. 
 

 

Figure 9. IP Deskset 

Summary of Contents for 47816A-700











Reviews: