14
I. CONNECTING THE WATER SUPPLY CORD
– see FIG. IV page 5
To the water inlet opening (1) - see FIG. III page 5 CONTROL PANEL, to the left of the control panel for the
washing machine / spin dryer, having raised the opening plug, connect the appropriate supply hose end (2) -
see FIG. II page 4 SET. Connect the other hose end to the tap. It is recommended to fix it to the tap by means of
a clamp (the fixing system is not included in the washing machine / spin dryer set).
II. WASHING
1.
Prepare the appropriate laundry load, in line with the technical parameters (maximum washing
machine load) and the guidelines below:
2.
Attach the drain hose to the drain hole
PLEASE NOTE!
To ensure correct discharge of water from the spin dryer and excess water from the washing machine,
connect the drain hose to the local sewer system before you start filling the device with water.
3.
Open the tap and fill the washing machine chamber with the appropriate amount of
hot
water, with
the temperature depending on the laundry type
WARNING!
For safety reasons, to avoid the risk of scalding, the temperature of water should not exceed 60
o
C!
The amount of water is indicated on the filter housing - see FIG. VI page 6
H
– maximum level of water
M
– minimum level of water
PLEASE NOTE!
Always fill the washing chamber with water to the level above the indicated minimum level.
PLEASE NOTE!
When the maximum level (H) is exceeded, water will overflow through the opening and will be drained by
the drain hose to the drain hole.
4.
Dissolve the appropriate amount of washing agent in water, appropriate for the laundry amount and
water hardness. Follow the washing agent manufacturer's instructions
5.
Place the prepared laundry load in the washing machine chamber
6.
Close the washing machine lid
7.
Connect the plug to the mains
8.
Using the washing timer knob (2) - see FIG. III page 5 CONTROL PANEL set the required washing time
(3, 6, 9, 12 or 15 minutes). You can also select the time between the said values
9.
Using the work mode knob (3) - see FIG. III page 5 CONTROL PANEL – set the washing machine work
mode
depending on the type of textiles and laundry soiling: gentle or standard
10.
The device starts running in line with the set washing parameters and after the cycle is finished, the
washing timer knob goes to 0 position automatically.
Remove all loose or metal
objects from the clothes to
be washed, such as safety
pins, clips, coins etc.
Ensure no chemically
contaminated clothes are
washed in the washing
machine.
Some clothes should be
washed inside out. This
refers to socks, knitwear,
trousers, T-shirts and
shirts.
Especially fine objects, like
tights, net curtains or small
ones, e.g. children socks or
handkerchiefs should be
washed only in a net bag or
a pillowcase.
Summary of Contents for XPB-680TP
