Rational SelfCookingCenter SCC Training Manual Download Page 41

Page: 41 / 91

- 41 -

V08 en, SCC

Changing PCB SCC

Software update to latest version

Reconnect unit to power supply and

switch unit ON

Insert SD card into new PCB

Removed SD card for usage in new

PCB.

Remove faulty PCB

Isolate unit from power supply

Changing pcb (pcb defective)

Only disconnect Software update

stick when basic SCC display is

shown.

All calibration and selftest data are located on both the PCB and the SD card Only the user

manual and the HACCP data are only on the PCB.

For this reason a software update must be done after changing the PCB.

Connect USB stick with latest

software to USB port.

Copy data from SD card to PCB

(press key 10 seconds)

Summary of Contents for SelfCookingCenter SCC




























































































Search results

Summary of Contents for SelfCookingCenter SCC

Reviews:

Related manuals for SelfCookingCenter SCC

Brands by name

Popular brands

Rational SelfCookingCenter SCC, Training Manual

Search results

Summary of Contents for SelfCookingCenter SCC

Reviews:

Related manuals for SelfCookingCenter SCC

Brands by name

Popular brands