background image

Ratek SWB10D Water Bath - Operating Manual 

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ 

Page 22 of 24

 

 

Electrical & Saf

Electrical & Saf

Electrical & Saf

Electrical & Safety Conformity

ety Conformity

ety Conformity

ety Conformity    

 
The water bath is made to international quality standards and is certified as conforming to the following standards: 
 

    

    

AS/NZS CISPR 14.1:2010 Electromagnetic compatibility - Requirements for household 
appliances, electric tools and similar apparatus – Emission. This forms the basis of 
compliance to the requirements of the Electromagnetic Compatibility Framework (‘C 
TICK’). 
 

    

The products described in this User Manual conforms to the requirements of the following 
European guidelines : 
 

 

Low voltage regulations with respect to legal harmonization of the member 
countries concerning electric devices for use within certain voltage limits. 

 

EMC guideline with respect to legal harmonization of the member countries 
concerning electromagnetic compatibility. 

 

The product has been tested in accordance with the following standards :  

IEC 61010-1 - Safety requirements for electrical equipment for 
measurement, control, and laboratory use - Part 1: General 
requirements. 
 
IEC 61010-2-010 - Safety requirements for electrical equipment 
for measurement, control and laboratory use - Part 2-010: 
Particular requirements for laboratory equipment for the heating 
of materials. 
 
IEC 61010-2-051 - Safety requirements for electrical equipment 
for measurement, control, and laboratory use - Part 2-051: 
Particular requirements for laboratory equipment for mixing and 
stirring. 
 
IEC 61326-1 - Electrical equipment for measurement, control and laboratory use - EMC 
requirements - Part 1: General requirements. 

 

RoHS

RoHS

RoHS

RoHS

  The product is categorized in both Category 8 and Category 9 of the Directive 2002/95/EC 

of the European Parliament, Restriction of Hazardous Substances, “RoHS Directive”. 
These categories are currently exempt from RoHS requirements. 

Summary of Contents for SWB10D240

























Reviews: