Ratek EOM5 User Manual Download Page 9

Ratek EOM5 Analogue Orbital Shaker – User Manual 

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 

Page 9 of 16

 

Using The Analogue Orbital Shaker 

 
 

Choosing a Suitable Vessel 

 

-

 

The Analogue Orbital Shaker should only be used with vessels that are sealed and are adequately secured to the mixing 
platform to prevent spillage whilst in use. 

 

 

 

Connecting Power 

 

CAUTION

 

The equipment must only be used with a protective earth power socket. The earth contact provides protection to the user and 
the equipment. If you do not have a protective earth power socket, or you are unsure as to whether you have a protective 
earth power socket, 

do not

 connect the equipment. In such cases you should consult your workplace administrator or electrical 

maintenance staff to determine if a protective earth power socket is available. 
 
The mains power supply must be rated to match the power requirement as identified on the product identification label on the 
bottom left corner of the rear panel. This is normally expressed in the format of Voltage Range and Frequency. 
 

A surge protected power outlet is strongly recommended as it provides some protection for the equipment in areas of 
poor electrical quality as well as providing some protection against lightning strikes. The equipment should be 
operated on a good, reliable supply of power at all times. 
 

Note: The Analogue Orbital Shaker should not be operated on the same electrical circuit as other high voltage household 
appliances such as fridges, clothes dryers, washing machines or other continuous operation high voltage devices. These types 
of devices can create power fluctuations that are undesirable for electrically sensitive equipment. Consult your workplace 
administrator or electrical maintenance staff if you are unsure. 

 
IMPORTANT: Use of an incorrect power supply will void the product warranty and waive all manufacturer liability for 
any and all damage caused by such use. If you are unsure about the rating of your power supply, consult your 
workplace administrator or electrical maintenance staff to determine if your power supply is suitable for use with this 
product before connecting the power lead. 

 

 

 

CAUTION 

Regularly check the mains power lead condition over the life of the product, and do not operate the equipment if you suspect 
there is damage to any part of the equipment or the mains power lead.

 

 

-

 

Using the supplied mains power lead, insert the socket end of the lead firmly into the mains power input receptacle (element 
5 in Figure 1) until it will move no further.  

-

 

Insert the plug end of the mains power supply lead firmly into a properly rated, protective earthed wall mounted power 
supply outlet. 

 
If there are double-adapters or oversized DC power packs causing obstruction of the mains power lead plug, these should first 
be removed. 

 

-

 

Ensuring your hands are dry, switch on the power on the mains power supply outlet. 

 

 

 

Adjusting The Mixing Control

 

 

 

 

The Analogue Orbital Shaker features adjustable mixing speed control to deliver gentle agitation through to vigorous mixing.  

To change the mixing speed 

-

 

Slowly turn the speed control knob (element 3 in Figure 1) clockwise to increase the speed, or anti-clockwise to decrease 
the speed. 

 

-

 

The speed may be adjusted during mixing to achieve the desired level of mixing inside the vessel.

 

 

 

 

 

Operating the Analogue Orbital Shaker

 

 

 

 

CAUTION 

When working with glass tubes, flasks, bottles, breakable or other brittle or fragile articles it is important to wear appropriate 
safety eyewear and protective gloves to ensure operator safety. In addition, the Analogue Orbital Shaker should be used in 
accordance with your operational health and safety policies. 

 

 

Summary of Contents for EOM5

















Reviews: