Ratek EOM5 User Manual Download Page 2

Ratek EOM5 Analogue Orbital Shaker – User Manual 

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 

Page 2 of 16

 

Thank you 

Thank you for purchasing a Ratek product. 
 
This User Manual will assist you in the correct installation and operation of the EOM5 Analogue Orbital Shaker, as well as explain the safety 
requirements for its use. 
 

Important: Please read the contents of this User Manual before unpacking and operating the product. 
 

Unpacking and Checking 

Once you have read these instructions in full and understand the installation and safety requirements including those for unpacking the carton, please 
carefully open the packing and slowly remove the product. Carefully inspect the condition of the product to ensure it has not been damaged in 
transit. Any damage should be reported immediately to the responsible carrier. If the product is damaged in any way, re-pack the product into the 
supplied packaging and notify the responsible carrier immediately.  
 

Important: Do not operate the equipment if it has been damaged in any way. Any failures resulting through the use of a damaged product 
will not be covered by the product warranty. 
 

Carton Contents 

Ensure that you have received all items outlined below before proceeding. If you have not received all components in the supplied carton, please re-
pack the carton and notify a Ratek Service representative immediately. Contact details are provided in the section of this User Manual titled “Ratek 
Service Contact Information” 

 

-

 

Ratek EOM5 Analogue Orbital Shaker 

-

 

Mains power input lead 

-

 

User Manual 

 

Summary of Contents for EOM5

















Reviews: