background image

24

Error code

E5

E8

U8

Troubleshooting

It can be eliminated after restarting the unit. If not, please 

E1

It can be eliminated after restarting the unit. If not, please 

It can be eliminated after restarting the unit. If not, please 

It can be eliminated after restarting the unit. If not, please 

Note: If there're other error codes, please contact qualified professionals for

service.

C5

F1

F2

F0

H6

It can be eliminated after restarting the unit. If not, please 

■ When below phenomenon occurs, pl

ease turn off air conditioner and discon-

   for service.      

      ● Power cord is overheating or damaged.

      ●

 There’s abnormal sound during operation.

      ●

 

Air switch trips o

ff frequently.

      ●

 Air conditioner gives off burning smell.

      ● Indoor unit is leaking.

■ If the air conditioner operates under a

bnormal conditions, it may cause

Malfunction analysis

Error code

● When air conditioner status is abnorm

al, temperature indica

tor on indoor unit will

   ation of error code.

WARNING

E6

It can be eliminated after restarting the unit. If not, please 

H3

It can be eliminated after restarting the unit. If not, please 

Summary of Contents for RS-S9KE

















































Reviews: