background image

Please contact the local agent for installation.

Indoor unit

1. There should be no obstruction near air

inlet and air outlet.

2. Select a location where the condensat-

ion water can be dispersed easily and
won't affect other people.
Select a location which is convenient to
connect the outdoor unit and near the
power socket.
Select a location which is out of reach
for children.
The location should be able to withstand
the weight of indoor unit and won't incr-
ease noise and vibration.

1.The place with strong heat sources,

   or volatile objects spread in the air.

,

The place with high-frequency
devices (such as welding machine,
medical equipment).
The place near coast area.
The place with oil or fumes in the air.

3.

2.

4.

5.

5.The place with sulfureted gas.
6.
7.

6. The appliance must be installed 2.5m

8.

7. Don't install the indoor unit right above

the electric appliance.

8. Please try your best to keep way from

Outdoor unit

1.

2.

3.
4. Make sure that the installation follows the requirement of installation

dimension diagram.
Select a location which is out of reach for children and far away from animals
or plants. If it is unavoidable, please add the fence for safety purpose.

5.

2

7

Tools for installation

Note:

Selection of installation location

Basic requirement

3.
4.

Select a location where the noise and outflow air emitted by the outdoor unit

The location should be well ventilated and dry, in which the outdoor unit
won't be exposed directly to sunlight or strong wind.
The location should be able to withstand the weight of outdoor unit.

1 Level meter

4 Drill head

7 Open-end wrench

10 Vacuum pump

13 Inner hexagon spanner

2 Screw driver

5 Pipe expander

8 Pipe cutter

11 Pressure meter

3 Impact drill

6 Torque wrench

9 Leakage detector

12 Universal meter

14 Measuring tape

Other places with special circumstances.
The appliance shall not be installed
in the laundry.
It’s not allowed to be installed on the
unstable or motive base structure (such
as truck) or in the corrosive environ-
ment (such as chemical factory).

    will not affect neighborhood.

Installing the unit in the following pla-
ces may cause malfunction. If it is un-
avoidable, please consult the local dealer:

Summary of Contents for RS-S9KE

















































Reviews: