4
New Generation Power Tools
–
RTRMAX
–
www.rtrmax.com
4
• Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
• Avoid the anormal body moving, when operating
the tools.
• Avoid accidental starting. Ensure the switch is in
the off position before plugging in. Carry power tools
with your finger on the switch or plugging in power
tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in
personal injury.
SIDE HANDLE
Use the side handle, during drill.
OPERATING
Always ue the correct supply voltage.
The voltage of the power source must agree with the
value given on the nameplate of the machine.
Machines designated for 230V can also be operated
with 220V.
SWITCH ON/OFF
Switching on: Press the on- off switch
Switching off: Release the on- off switch
.
CONTINUOUS OPERATION
Push the variable speed switch trigger and at the
same time push the continuous operation lock .
The stop continuous operating, push variable speed
switch and then release.
OPERATING MODE:
This hammer drill canbe used as listed below:
Drilling:
Drilling and screwing steel,wood and plastic
workpieces.
Hammer drilling:
In concrete or wall stone
Hammering:
Chipping, chisel and demolation applications
INSERTING SDS-PLUS BITS
SDS-Plus accesories are used in your hammer drill.
Clean bits holder front cover and grease. Insert SDS-
Plus, steel ball support.
Pull back the steel ball support and rotate the steel
ball support by depressing until SDS-Plus bit will be
fitted. Pull the bit to check if it is locked to holder.
In hammering function, when the bit is locked in
holder, it needs to move a few centimeters as axial .
ROTATING SPEED SELECTION
Required rotating speed can be adjusted by selecting.
Required rotating speed depends on material and it
can be determined best by trying.
After working low rotating speed for cooling the tool,
run the tool no-load about 3 minute.
CHANGING THE ROTATING DIRECTION
Change the rotating direction, when just the switch
is off. Devir istikametini sadece dururken değiştirin.
The rotating direction can be change by
forward/reverse switch.
(When the variable speed
switch is on, forward/reverse switch is locked)
Right direction
Push te forward/reverse switch to right till the last
(For loosing screws and sockets).
Left direction
Push te forward/reverse switch to right till the last
(For loosing screws and sockets).
MAINTENANCE AND CLEANING
Before any work on the machine itself, pull the
mains plug.
For safe and proper working, always keep the
machine and the ventilation slots clean.
If the machine has accumulative worked 40 hours or
drilled more than 2000 holes, or find that impact
force isn’t big, to keep machine working normally,
please use the Grease which provided by
manufacturer, add it into the cylinder, it can prolong
the life of machine.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorized customer services agent
for
RTRMAX power tools
.
New Generation Power Tools
–
RTRMAX
–
www.rtrmax.com
4
• Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
• Avoid the anormal body moving, when operating
the tools.
• Avoid accidental starting. Ensure the switch is in
the off position before plugging in. Carry power tools
with your finger on the switch or plugging in power
tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in
personal injury.
SIDE HANDLE
Use the side handle, during drill.
OPERATING
Always ue the correct supply voltage.
The voltage of the power source must agree with the
value given on the nameplate of the machine.
Machines designated for 230V can also be operated
with 220V.
SWITCH ON/OFF
Switching on: Press the on- off switch
Switching off: Release the on- off switch
.
CONTINUOUS OPERATION
Push the variable speed switch trigger and at the
same time push the continuous operation lock .
The stop continuous operating, push variable speed
switch and then release.
OPERATING MODE:
This hammer drill canbe used as listed below:
Drilling:
Drilling and screwing steel,wood and plastic
workpieces.
Hammer drilling:
In concrete or wall stone
Hammering:
Chipping, chisel and demolation applications
INSERTING SDS-PLUS BITS
SDS-Plus accesories are used in your hammer drill.
Clean bits holder front cover and grease. Insert SDS-
Plus, steel ball support.
Pull back the steel ball support and rotate the steel
ball support by depressing until SDS-Plus bit will be
fitted. Pull the bit to check if it is locked to holder.
In hammering function, when the bit is locked in
holder, it needs to move a few centimeters as axial .
ROTATING SPEED SELECTION
Required rotating speed can be adjusted by selecting.
Required rotating speed depends on material and it
can be determined best by trying.
After working low rotating speed for cooling the tool,
run the tool no-load about 3 minute.
CHANGING THE ROTATING DIRECTION
Change the rotating direction, when just the switch
is off. Devir istikametini sadece dururken değiştirin.
The rotating direction can be change by
forward/reverse switch.
(When the variable speed
switch is on, forward/reverse switch is locked)
Right direction
Push te forward/reverse switch to right till the last
(For loosing screws and sockets).
Left direction
Push te forward/reverse switch to right till the last
(For loosing screws and sockets).
MAINTENANCE AND CLEANING
Before any work on the machine itself, pull the
mains plug.
For safe and proper working, always keep the
machine and the ventilation slots clean.
If the machine has accumulative worked 40 hours or
drilled more than 2000 holes, or find that impact
force isn’t big, to keep machine working normally,
please use the Grease which provided by
manufacturer, add it into the cylinder, it can prolong
the life of machine.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorized customer services agent
for
RTRMAX power tools
.
New Generation Power Tools
–
RTRMAX
–
www.rtrmax.com
4
• Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
• Avoid the anormal body moving, when operating
the tools.
• Avoid accidental starting. Ensure the switch is in
the off position before plugging in. Carry power tools
with your finger on the switch or plugging in power
tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in
personal injury.
SIDE HANDLE
Use the side handle, during drill.
OPERATING
Always ue the correct supply voltage.
The voltage of the power source must agree with the
value given on the nameplate of the machine.
Machines designated for 230V can also be operated
with 220V.
SWITCH ON/OFF
Switching on: Press the on- off switch
Switching off: Release the on- off switch
.
CONTINUOUS OPERATION
Push the variable speed switch trigger and at the
same time push the continuous operation lock .
The stop continuous operating, push variable speed
switch and then release.
OPERATING MODE:
This hammer drill canbe used as listed below:
Drilling:
Drilling and screwing steel,wood and plastic
workpieces.
Hammer drilling:
In concrete or wall stone
Hammering:
Chipping, chisel and demolation applications
INSERTING SDS-PLUS BITS
SDS-Plus accesories are used in your hammer drill.
Clean bits holder front cover and grease. Insert SDS-
Plus, steel ball support.
Pull back the steel ball support and rotate the steel
ball support by depressing until SDS-Plus bit will be
fitted. Pull the bit to check if it is locked to holder.
In hammering function, when the bit is locked in
holder, it needs to move a few centimeters as axial .
ROTATING SPEED SELECTION
Required rotating speed can be adjusted by selecting.
Required rotating speed depends on material and it
can be determined best by trying.
After working low rotating speed for cooling the tool,
run the tool no-load about 3 minute.
CHANGING THE ROTATING DIRECTION
Change the rotating direction, when just the switch
is off. Devir istikametini sadece dururken değiştirin.
The rotating direction can be change by
forward/reverse switch.
(When the variable speed
switch is on, forward/reverse switch is locked)
Right direction
Push te forward/reverse switch to right till the last
(For loosing screws and sockets).
Left direction
Push te forward/reverse switch to right till the last
(For loosing screws and sockets).
MAINTENANCE AND CLEANING
Before any work on the machine itself, pull the
mains plug.
For safe and proper working, always keep the
machine and the ventilation slots clean.
If the machine has accumulative worked 40 hours or
drilled more than 2000 holes, or find that impact
force isn’t big, to keep machine working normally,
please use the Grease which provided by
manufacturer, add it into the cylinder, it can prolong
the life of machine.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorized customer services agent
for
RTRMAX power tools
.
Summary of Contents for Z1A-HB-2614 / RR RH-10
